Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

DTC    C2174/74    Vehicle Speed Signal Malfunction

DTC    C2191/91    Vehicle Speed Signal Error (Test Mode DTC)

for Preparation Click here


DESCRIPTION

Speed signals are input into the tire pressure warning ECU from the combination meter. At the same time, the G-SW in the tire pressure warning valve and transmitter detects driving conditions, and sends signals to the tire pressure warning ECU. If the speed signal from the combination meter stops and the G-SW signal in the tire pressure warning valve and transmitter indicates that the vehicle is being driven, DTC C2174/74 is stored.
DTC C2191/91 is stored only during the signal check.

DTC Code
Detection Condition
Trouble Area
C2174/74
Vehicle speed signal malfunction
  1. Combination meter
  2. Vehicle speed signal circuit
  3. Harness or connector
  4. Tire pressure warning ECU
  5. Tire pressure warning valve and transmitter
C2191/91
Test mode procedure is performed
  1. Meter / gauge system (speed signal)
  2. Vehicle speed signal circuit
  3. Harness or connector
  4. Tire pressure warning ECU

WIRING DIAGRAM


C179102E03


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.

HINT:
When the speedometer needle is not moving, first troubleshoot the meter/gauge system (Click here).

1.READ VALUE USING DATA LIST (VEHICLE SPEED)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check that the values indicated on the Techstream and on the combination meter are the same.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed
    Speed indicated on combination meter

    OK:
    Vehicle speed indicated on the Techstream indicates the actual speed.



NG
Go to step 3
OK


2.CHECK DTC
  1. Perform a driving test.

  1. Check for DTCs.

    HINT:
    The time required for DTC C2174 to be stored is 20 minutes.

    Result 
    Result
    Proceed to
    DTC C2174 is not output
    A
    DTC C2174 is output
    B



B
Go to step 6
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER)
  1. Disconnect the J31 tire pressure warning ECU connector.



    C158878E01
  1. Disconnect the J28 meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J31-2 (SPD) - J28-35 (+S)
    Always
    Below 1 Ω
    J31-2 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

C240446E02

  1. Disconnect the A17 skid control ECU connector.

  1. Disconnect the J28 meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-3 (SP1) - J28-36 (S1)
    Always
    Below 1 Ω
    A17-3 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK DTC (SFI SYSTEM)
  1. Check for DTCs.

    HINT:
    1. for 1GR-FE (Click here).
    2. for 1UR-FE (Click here).
    3. for 3UR-FE (Click here).
    4. for 3UR-FBE (Click here).

    Result 
    Result
    Proceed to
    DTC P0500 is not output
    A
    DTC P0500 is output
    B



B
REPLACE COMBINATION METER (Click here)
A


6.REPLACE TIRE PRESSURE WARNING ECU
  1. Replace the tire pressure warning ECU (Click here).


NEXT


7.PERFORM REGISTRATION OF TRANSMITTER ID
  1. Perform registration (Click here).


NEXT


8.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


9.CHECK DTC
  1. Perform a driving test.

  1. Check for DTCs.

    HINT:
    The time required for DTC C2174 to be stored is 20 minutes.

    Result 
    Result
    Proceed to
    DTC C2174 is output
    A
    DTC C2174 is not output
    B



B
END
A

REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (Click here)