FUEL TANK > INSTALLATION |
| 1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Apply a light coat of gasoline to a new gasket, and install it to the fuel tank assembly.
![]() |
Align the protrusion of the fuel suction with pump and gauge tube assembly with the groove of the fuel tank assembly.
| *1 | Protrusion |
| *2 | Groove |
Install the fuel suction with pump and gauge tube assembly to the fuel tank assembly.
Put a new retainer on the fuel tank assembly. While holding the fuel suction with pump and gauge tube assembly, tighten the retainer one complete turn by hand.
![]() |
Set SST on the retainer.
![]() |
Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank assembly, as shown in the illustration.
| *1 | Fuel Tank Side Mark |
| *2 | Retainer Side Mark |
![]() |
Install the fuel tank return tube and fuel tank main tube sub-assembly with the 2 tube joint clips.
![]() |
| *1 | Fuel Tube Joint |
| *2 | O-Ring |
| *3 | Fuel Tube |
| *4 | Tube Joint Clip |
| *a | CORRECT |
| *b | INCORRECT |
| 2. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Install the fuel tank to filler pipe hose to the fuel tank assembly.
| 3. INSTALL NO. 1 FUEL TANK HEAT INSULATOR |
Install the No. 1 fuel tank heat insulator with the 4 clips and nut.
| 4. INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY |
Install the fuel tank inlet pipe sub-assembly with the 2 nuts.
| 5. INSTALL FUEL TANK ASSEMBLY |
Set the fuel tank assembly on a engine lifter and raise the fuel tank assembly.
Attach the harness clamp and connect the fuel pump connector to the fuel tank assembly.
Raise the engine lifter.
Install the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 pins and 2 clips.
Connect the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 bolts.
| 6. CONNECT NO. 1 CANISTER OUTLET HOSE |
Connect the No. 1 canister outlet hose to the fuel tank inlet pipe sub-assembly.
Attach the hose to the No. 1 breather tube clamp.
| 7. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank assembly to fuel tank to filler pipe hose to the fuel tank inlet pipe sub-assembly.
Connect the fuel tank breather tube (Click here).
Attach the fuel tank to filler pipe hose and fuel tank breather tube to the No. 1 breather tube clamp.
| 8. CONNECT WIRE HARNESS |
Attach the harness clamp to the fuel tank assembly.
| 9. CONNECT VENT LINE HOSE |
![]() |
Connect the vent line hose and install the retainer.
| *1 | Retainer |
![]() | Pull Down |
| 10. CONNECT FUEL TANK RETURN TUBE |
Connect the fuel tank return tube (Click here).
| 11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
Connect the fuel tank main tube sub-assembly (Click here).
| 12. INSTALL FUEL TANK CAP |
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 14. INSPECT FOR FUEL LEAK |
Make sure that there are no fuel leaks after performing maintenance on the fuel system.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no leaks from the fuel system.
If there are fuel leaks, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.