Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injector assemblies are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A247759E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A208644E20
  1. Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Turn the ignition switch off.



NG
Go to step 5
OK


2.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D74-43 (E01) - Body ground
    Always
    Below 1 Ω
    D74-42 (E02) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the No. 1 integration relay connector.

  1. Disconnect the fuel injector assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1B-8 - D11-1
    Always
    Below 1 Ω
    1B-8 - D26-1
    Always
    Below 1 Ω
    1B-8 - D13-1
    Always
    Below 1 Ω
    1B-8 - D24-1
    Always
    Below 1 Ω
    1B-8 - D15-1
    Always
    Below 1 Ω
    1B-8 - D22-1
    Always
    Below 1 Ω
    1B-8 or D11-1 - Body ground
    Always
    10 kΩ or higher
    1B-8 or D26-1 - Body ground
    Always
    10 kΩ or higher
    1B-8 or D13-1 - Body ground
    Always
    10 kΩ or higher
    1B-8 or D24-1 - Body ground
    Always
    10 kΩ or higher
    1B-8 or D15-1 - Body ground
    Always
    10 kΩ or higher
    1B-8 or D22-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)