Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E04


DTC Code
DTC Detection Condition
Trouble Area
P0500
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(2 trip detection logic)
  1. Open or short in speed signal circuit
  2. Wheel speed sensor
  3. Combination meter
  4. ECM
  5. Skid control ECU

MONITOR DESCRIPTION


  1. The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main)
Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU
Required Sensors/Components (Related)
Park / Neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor, Throttle Position (TP) sensor and Mass Air Flow (MAF) meter
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Time after ignition switch off to ON
3 seconds or more
Vehicle speed
9 km/h (5.6 mph) or more
Battery voltage
8 V or more
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Vehicle speed sensor signal
No pulse input

CONFIRMATION DRIVING PATTERN


A198825E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
  8. Stop the vehicle.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0500.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A244852E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING TECHSTREAM (VEHICLE SPD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the Techstream.

    OK:
    Vehicle speeds displayed on Techstream and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the J28 combination meter connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    J28-35 (+S) - A24-13 (SPD)
    Always
    Below 1 Ω
    J28-35 (+S) or A24-13 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE) 

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
A127854E09
  1. Disconnect the J28 combination meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-35 (+S) - Body ground
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A127943E26
  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-35 (+S) - Body ground
    1. Ignition switch ON
    2. Wheel is turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 6
OK

REPLACE ECM 

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
A127943E64
  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-36 (SI) - Body ground
    1. Ignition switch ON
    2. Wheel is turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 7
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR)
  1. Disconnect the combination meter connector.

  1. Disconnect the brake actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    J28-36 (SI) - A17-3 (SP1)
    Always
    Below 1 Ω
    J28-36 (SI) - or A17-3 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
END
OK

REPLACE BRAKE ACTUATOR ASSEMBLY