DIFFERENTIAL CARRIER OIL SEAL (for 1GR-FE, 1UR-FE) > REPLACEMENT |
| 1. DRAIN DIFFERENTIAL OIL |
Stop the vehicle on a level place.
for Front Differential:
Using a 10 mm hexagon wrench, remove the filler plug and gasket.
Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.
Using a 10 mm hexagon wrench, install a new gasket and the drain plug.
for Rear Differential:
Remove the filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
| 2. REMOVE PROPELLER SHAFT ASSEMBLY |
Remove the propeller shaft for 2WD (Click here).
Remove the propeller shaft for 4WD (Click here).
| 3. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange, remove the nut.
| 4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using SST, remove the companion flange.
| 5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| 6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front bearing (inner race).
![]() |
Using SST, remove the bearing (outer race).
| 8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
| 9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
Install a new bearing spacer.
| 10. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a hammer, tap in the bearing (outer race).
![]() |
Using SST and the companion flange, install the bearing (inner race). Then remove the companion flange.
| 11. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 12. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.
Coat the lip of the oil seal with MP grease.
| 13. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
Place the companion flange on the drive pinion.
Coat the threads of a new nut with hypoid gear oil.
![]() |
Using SST to hold the companion flange, tighten the nut.
| 14. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| Item | Specified Condition |
| New bearing | 1.04 to 1.69 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf) |
| Reused bearing | 0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf) |
| 15. STAKE REAR DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 16. INSTALL PROPELLER SHAFT ASSEMBLY |
Install the propeller shaft for 2WD (Click here).
Install the propeller shaft for 4WD (Click here).
| 17. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 1UR-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.