Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER ASSEMBLY


C209683E01
  1. Using a vernier caliper and straightedge, measure dimension "A" between the transmission fitting surface of the engine*1 and the torque converter fitting surface of the drive plate*2. (#)



    C209685E01
  1. Aligning the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.



    C209687E01
  1. Mesh the splines of the stator shaft and stator while turning the torque converter clutch.

    HINT:
    Turn the torque converter clutch approximately 180°.



    C210217E01
  1. Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to mesh the key of the oil pump drive gear into the slot on the torque converter clutch.

    NOTICE:
    Do not push on the torque converter when aligning the matchmarks.



    C209689E01
  1. Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that B is greater than A measured in the first step.

    Standard distance:
    A + 1 mm (0.0394 in.) or more



2. INSTALL TRANSMISSION CONTROL CABLE BRACKET
  1. Install the bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the front left bank bracket with the bolt.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

  1. Install the rear left bank bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



4. INSTALL TRANSMISSION OIL COOLER ASSEMBLY


C157012E01
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 hoses to the transmission oil cooler spacer with the 2 clips.



    C157010E01
  1. Install the transmission oil cooler with transmission oil cooler spacer with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 hoses with the 2 clips.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C209691E01
  1. Apply clutch spline grease to the surface of the torque converter clutch centerpiece that contacts the crankshaft.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.0353 oz.)



    C209695E01
  1. Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.

  1. Install the transmission with the 9 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



6. CONNECT NO. 1 WATER BY-PASS PIPE


C157015E01
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



7. CONNECT WIRE HARNESS AND CONNECTOR


    C155912E02
  1. Connect the park/neutral start switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the harness clamp with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the 4 connector clamps and 4 harness clamps.

  1. Tilt up the automatic transmission.

  1. Connect the ground cable with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



8. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



10. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
  1. Turn the crankshaft to gain access to the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then install the remaining 5 bolts.

  1. Install the flywheel housing side cover.



11. INSTALL STARTER ASSEMBLY (for 1.6 kW Type)
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



12. INSTALL STARTER ASSEMBLY (for 1.4 kW Type)
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



13. INSTALL STARTER COVER (for 1.4 kW Type)
  1. Install the starter cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



14. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



15. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A222094E01
  1. Install a new gasket to the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.



    A237700E01
  1. Temporarily install the manifold with the new nut labeled 1.

  1. Install the remaining 5 new nuts and tighten the nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



16. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



17. INSTALL NO. 2 AIR TUBE


    A239089E01
  1. Install 2 new gaskets to the No. 2 air tube as shown in the illustration.
    Text in Illustration 
    *1
    New Gasket
    *2
    No. 2 Air Tube

  1. Install the No. 2 air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL NO. 2 MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Connect the wire harness connector.



19. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the fender apron seal with the 5 clips.



20. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C158380E01
  1. Connect the control cable with a new clip and nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the inside of the vehicle.



21. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. for Regular Cab Standard Deck:
    (Click here).

  1. except Regular Cab Standard Deck:
    (Click here).



22. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


24. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)


25. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    10.7 liters (11.3 US qts, 9.4 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the inlet radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Measurement Condition 
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the inlet and outlet radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the outlet radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
    If the coolant level is below the FULL line, repeat steps *4 through *8.
    If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.



26. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



27. ADJUST SHIFT LEVER POSITION (for Column Shift Type)
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



28. ADJUST SHIFT LEVER POSITION (for Floor Shift Type)
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



29. INSPECT SHIFT LEVER POSITION (for Column Shift Type)
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



30. INSPECT SHIFT LEVER POSITION (for Floor Shift Type)
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



31. CHECK FOR EXHAUST GAS LEAK


32. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



33. PERFORM RESET MEMORY
(Click here)