AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 4. DRAIN AUTOMATIC TRANSMISSION FLUID |
Remove the drain plug and gasket, and drain ATF.
Install a new gasket and the drain plug.
| 5. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

| *1 | Radiator Reservoir | *2 | Radiator Cap |
| *3 | Radiator Drain Cook Plug | *4 | Cylinder Block Drain Cock Plug |
Remove the radiator cap. Then drain the coolant.
Tighten the 2 cylinder block drain cock plugs.
Tighten the radiator drain cock plug by hand.
| 6. REMOVE PROPELLER SHAFT ASSEMBLY |
| 7. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
for Regular Cab Standard Deck:
(Click here).
except Regular Cab Standard Deck:
(Click here).
| 8. REMOVE FRONT FENDER APRON SEAL REAR LH |
Remove the 5 clips and fender apron seal.
| 9. REMOVE NO. 2 MANIFOLD STAY |
Disconnect the wire harness connector.
![]() |
Remove the 3 bolts and No. 2 manifold stay.
| 10. REMOVE NO. 2 AIR TUBE |
![]() |
Remove the 2 bolts, 2 nuts and No. 2 air tube.
Remove the 2 gaskets from the No. 2 air tube.
| 11. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and heat insulator.
| 12. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Remove the 6 nuts, manifold and gasket.
| 13. REMOVE MANIFOLD STAY |
![]() |
Remove the 3 bolts and manifold stay.
| 14. REMOVE STARTER COVER (for 1.4 kW Type) |
![]() |
Remove the 3 bolts and starter cover.
| 15. REMOVE STARTER ASSEMBLY (for 1.4 kW Type) |
![]() |
Remove the bolt and disconnect the ground wire.
Disconnect the starter connector.
Remove the nut and bolt, and then disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 16. REMOVE STARTER ASSEMBLY (for 1.6 kW Type) |
![]() |
Remove the bolt and disconnect the ground wire.
Disconnect the starter connector.
Remove the terminal cap.
Remove the nut and disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 17. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
![]() |
Remove the flywheel housing side cover.
![]() |
Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.
| 18. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut and clip, and disconnect the transmission control cable.
| 19. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Support the transmission with a transmission jack.
Lift the transmission slightly from the crossmember.
| 20. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts of the rear engine mounting insulator.
![]() |
Remove the 4 nuts, 4 washers, 4 bolts and frame crossmember.
| 21. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
![]() |
Remove the 4 bolts and rear engine mounting insulator from the transmission.
| 22. DISCONNECT WIRE HARNESS AND CONNECTOR |
![]() |
Remove the bolt and disconnect the ground cable.
![]() |
Tilt the transmission downward.
![]() |
Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.
Disconnect the 4 connector clamps and 4 harness clamps.
Remove the bolt and disconnect the harness clamp and wire harness.
| 23. DISCONNECT NO. 1 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts and disconnect the 2 water by-pass hoses from the transmission oil cooler, and separate the by-pass pipe from the automatic transmission.
| 24. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Remove the 9 bolts and transmission.
| 25. REMOVE TRANSMISSION OIL COOLER ASSEMBLY |
![]() |
Disconnect the 2 oil cooler hoses.
Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.
![]() |
Remove the 3 bolts and separate the transmission oil cooler from the transmission oil cooler spacer.
Remove the 2 O-rings.
| 26. REMOVE HARNESS CLAMP BRACKET |
Remove the 2 bolts and 2 brackets.
| 27. REMOVE TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Remove the 2 bolts and bracket.
| 28. REMOVE TORQUE CONVERTER ASSEMBLY |
| 29. INSPECT TORQUE CONVERTER ASSEMBLY |