AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 4. DRAIN AUTOMATIC TRANSMISSION FLUID |
Remove the drain plug and gasket, and drain the ATF.
Install a new gasket and the drain plug.
| 5. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.

Tighten the radiator drain cock plug by hand.
| 6. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
| 7. REMOVE PROPELLER SHAFT ASSEMBLY |
| 8. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
for Regular Cab Standard Deck:
(Click here)
except Regular Cab Standard Deck:
(Click here).
| 9. REMOVE STARTER ASSEMBLY |
| 10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut and clip, and disconnect the shift control cable.
| 11. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
![]() |
Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.
| 12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.
| 13. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts of the rear engine mounting insulator.
![]() |
Remove the 4 nuts, 4 washers, 4 bolts and frame crossmember.
| 14. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
![]() |
Remove the 4 bolts and rear engine mounting insulator from the transmission.
| 15. DISCONNECT WIRE HARNESS AND CONNECTOR |
![]() |
Remove the bolt and disconnect the ground cable.
![]() |
Tilt the transmission downward.
![]() |
Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control side connectors.
Disconnect the 3 connector clamps and 7 harness clamps.
Remove the 2 bolts and disconnect the harness clamps and wire harness.
| 16. DISCONNECT BREATHER PLUG HOSE |
![]() |
Disconnect the 3 breather plug hoses from the harness clamp bracket.
| 17. DISCONNECT NO. 2 WATER BY-PASS PIPE (w/ Trailer Towing System) |
![]() |
Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.
![]() |
Disconnect the 2 transmission oil cooler hoses from the transmission oil thermostat.
| 18. DISCONNECT NO. 2 WATER BY-PASS PIPE (w/o Trailer Towing System) |
![]() |
Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then separate the by-pass pipe from the automatic transmission.
| 19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Remove the 10 bolts and transmission.
| 20. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System) |
![]() |
Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.
Separate the transmission oil cooler from the transmission oil thermostat.
Remove the 4 O-rings.
| 21. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System) |
![]() |
Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.
Separate the transmission oil cooler from the transmission oil cooler spacer.
Remove the 4 O-rings.
| 22. REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY |
Remove the bolt and bracket
| 23. REMOVE HARNESS CLAMP BRACKET |
Remove the 3 bolts and 3 brackets.
| 24. REMOVE TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Remove the 2 bolts and bracket.
| 25. REMOVE TORQUE CONVERTER ASSEMBLY |
| 26. INSPECT TORQUE CONVERTER ASSEMBLY |