Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1620/21    Driver Side - Side Airbag Sensor Circuit Malfunction

DTC    B1625/22    Front Passenger Side - Side Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor LH and RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1620/21or B1625/22 is recorded when a malfunction is detected in the side airbag sensor LH or RH circuit.

DTC Code
Detection Condition
Trouble Area
B1620/21
When one of the following conditions is met:
  1. Side airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor LH
  2. Center airbag sensor assembly
B1625/22
When one of the following conditions is met:
  1. Side airbag sensor RH malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor RH
  2. Center airbag sensor assembly

WIRING DIAGRAM


C243661E01


C243661E02


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1620 is output
    B
    DTC B1625 is output
    C



A
USE SIMULATION METHOD TO CHECK (Click here)

B
Go to step 6
C


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)

C243663E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q14-1 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    Q14-2 (BBR+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q14-1 (BBR-) - Q14-2 (BBR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q14-1 (BBR-) - Q4-2 (BBR+)
    Always
    1 MΩ or higher
    Q14-1 (BBR-) - Body ground
    Q14-2 (BBR+) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK SIDE AIRBAG SENSOR RH
C146230E03
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1620 is output
    B
    DTC B1625 is output (for Column Shift Type)
    C
    DTC B1625 is output (for Floor Shift Type)
    D

    HINT:
    Codes other than DTC B1620 and B1625 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


7.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


8.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)

C243664E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P18-1 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V
    P18-2 (BBL+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P18-1 (BBL-) - P18-2 (BBL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    P18-1 (BBL-) - P18-2 (BBL+)
    Always
    1 MΩ or higher
    P18-1 (BBL-) - Body ground
    P18-2 (BBL+) - Body ground



NG
REPLACE FLOOR WIRE
OK


9.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1625 is output
    B
    DTC B1620 is output (for Column Shift Type)
    C
    DTC B1620 is output (for Floor Shift Type)
    D

    HINT:
    Codes other than DTC B1620 and B1625 maybe output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)