DTC B1830/57 Short in Driver Side Curtain Shield Squib Circuit |
DTC B1831/57 Open in Driver Side Curtain Shield Squib Circuit |
DTC B1832/57 Short to GND in Driver Side Curtain Shield Squib Circuit |
DTC B1833/57 Short to B+ in Driver Side Curtain Shield Squib Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1830/57 | When one of the following conditions is met:
|
|
| B1831/57 | When one of the following conditions is met:
|
|
| B1832/57 | When one of the following conditions is met:
|
|
| B1833/57 | When one of the following conditions is met:
|
|

| 1.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the curtain shield airbag LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK (for Regular Cab and Double Cab) | A |
| OK (for CrewMax) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P3-1 (ICL-) - Body ground | Ignition switch ON | Below 1 V |
| P3-2 (ICL+) - Body ground |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P3-1 (ICL-) - P3-2 (ICL+) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P3-1 (ICL-) - P3-2 (ICL+) | Always | 1 MΩ or higher |
| P3-1 (ICL-) - Body ground | ||
| P3-2 (ICL+) - Body ground |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connectors to the curtain shield airbag LH and the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1830, B1831, B1832 or B1833 is output (for Column Shift Type) | A |
| DTC B1830, B1831, B1832 or B1833 is output (for Floor Shift Type) | B |
| DTC B1830, B1831, B1832 or B1833 is not output | C |
|
| ||||
|
| ||||
| C | ||
| ||