Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P050B    Cold Start Ignition Timing Performance

for Preparation Click here


DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature between -10 and 50°C (14 and 122°F). The DTC will be stored after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature below 50°C (122°F), the ECM checks the ignition timing during engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

NOTICE:
When the cable is disconnected from the negative battery terminal during inspections or repairs, the ISC (Idle Speed Control) learned values are cleared. This DTC cannot be stored with the ISC learned values cleared.

HINT:
ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A234892E04


DTC No.
DTC Detection Condition
Trouble Area
P050B
Insufficient ignition timing retard at cold start (2 trip detection logic).
  1. Throttle body with assembly
  2. Mass air flow meter
  3. PCV system
  4. Air cleaner filter element sub-assembly
  5. Intake system
  6. VVT system
  7. ECM
  8. Wire harness or connector

MONITOR STRATEGY


Related DTCs
P050B: Cold start ignition timing performance
Required Sensors/Components (Main)
Throttle body with motor assembly
Required Sensors/Components (Related)
Mass air flow meter
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0705 (Shift lever position switch)
P219A, P219B (Air-fuel ratio imbalance)
Battery voltage
8 V or higher
Time after engine start
3 seconds or more
Starter
OFF
Engine coolant temperature at engine start
-10°C (14°F) or higher
Engine coolant temperature
-10 to 50°C (14 to 122°F)
Engine idling time
3 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 3 km/h (1.875 mph)
Atmospheric pressure
76 kPa (570 mmHg) or higher

TYPICAL MALFUNCTION THRESHOLDS


Accumulated time when ignition timing retard is cut off
8 seconds or more

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
  7. Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).
  8. Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.
  9. Idle the engine for 1 minute or more [B].
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P050B.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. DTC P050B may be stored when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.

    Symptom
    Factor
    Trouble Area
    Low idle speed when engine is cold (immediately after engine start)
    Excessive engine friction
    1. Engine oil deterioration
    2. Drive belt tension
    3. A/C compressor
    4. Generator
    5. Vane pump
    Rough idle when engine is cold (immediately after engine start)
    Abnormal combustion
    Fuel quality
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P050B is output
    A
    P050B and other DTCs are output
    B

    HINT:
    If any DTCs other than P050B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim to check the characteristic deviation of the mass air flow meter.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream.

  1. Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

    OK:
    Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 5
OK


3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
  1. Check for deposits around the throttle valve and check the throttle valve condition.

    OK:
    No deposits around throttle valve and throttle valve moves smoothly.



OK
Go to step 14

NG
Go to step 4

4.REPAIR OR REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
  1. Repair or replace the throttle body with motor assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the throttle body with motor assembly (Click here).



NEXT
Go to step 14

5.CHECK PCV HOSE
  1. Check the PCV hose connections .

    OK:
    PCV hose is connected correctly and is not damaged.



NG
Go to step 10
OK


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks .

    OK:
    No leak in the intake system.



NG
Go to step 11
OK


7.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

    OK:
    The air cleaner filter element is not excessively contaminated with dirt or oil.



NG
Go to step 12
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

    OK:

    Techstream Operation
    Engine Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1 or VVT OCV Duty #2 and VVT Change Angle #2] (Click here).



NG
Go to step 13
OK


9.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec and 25.8 gm/sec (shift lever: N; A/C: off).



OK
Go to step 14

NG
Go to step 15

10.REPAIR OR REPLACE PCV HOSE
  1. Repair or replace the PCV hose.



NEXT
Go to step 14

11.REPAIR OR REPLACE INTAKE SYSTEM
  1. Repair or replace the intake system.

HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NEXT
Go to step 14

12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Replace the air cleaner filter element sub-assembly.



NEXT
Go to step 14

13.CHECK AND REPAIR VVT SYSTEM
  1. Check and repair the VVT system.

    HINT:
    1. Refer to DTC P0011 Inspection Procedure (VVT system for intake camshaft) .
    2. Refer to DTC P0014 Inspection Procedure (VVT system for exhaust camshaft) .


NEXT


14.CHECK WHETHER DTC OUTPUT RECURS

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (No DTC is output)
    A
    ABNORMAL (P050B is output)
    B



B
Go to step 15
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

15.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (P050B is output)
    A
    NORMAL (No DTC is output)
    B



B
END
A


17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D7-5 (VG) - D74-74 (VG)
    Always
    Below 1 Ω
    D7-4 (E2G) - D74-75 (E2G)
    Always
    Below 1 Ω
    D7-5 (VG) or D74-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    1. If the result of the inspection performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).


NEXT


19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14°F and 122°F).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (No DTC is output)
    A
    ABNORMAL (P050B is output)
    B



B
REPLACE ECM (Click here)
A

END