Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Driver Side Door Key Lock and Unlock Switch Circuit

for Preparation Click here


DESCRIPTION

The Front door key lock and unlock switch LH is built into the Front door lock motor LH. When the Front door key cylinder LH is turned to lock all the doors using the key, there is continuity between terminals L and E of the key lock and unlock switch. When the cylinder is turned to unlock the doors, there is continuity between terminals UL and E. Terminals L2 and UL3 of the main body ECU are connected to the door lock motor, and door lock/unlock request signals (by key) are input to the main body ECU. The main body ECU constantly applies voltage to terminal L of the front door lock motor LH via terminal L2. When the front door key cylinder LH is turned to lock all the doors using the key, current flows from terminal L2 to terminal L. The main body ECU also applies constant voltage to terminal UL of the door lock motor via terminal UL3. When the door key cylinder is turned to unlock the doors using the key, current flows from terminal UL3 to terminal UL.

WIRING DIAGRAM


E144955E05


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Check the Data List to ensure proper functioning of the door key lock and unlock switch.

    Main Body 
    Tester Display
    Measurement item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door lock/unlock switch lock signal (Key-linked lock switch) / ON or OFF
    ON: Driver side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder is not turned
    -
    Door Key SW-Unlock
    Driver door lock/unlock switch unlock signal (Key-linked unlock switch) / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -
    D Door Key SW-UL
    Driver door lock/unlock switch unlock signal (2 step key-linked unlock switch) / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR LOCK MOTOR ASSEMBLY LH (DOOR KEY LOCK AND UNLOCK SWITCH)
E146713E01
  1. Remove the front door lock motor LH.

    1. for Double Cab: (Click here)
    2. for Regular Cab: (Click here)
    3. for CrewMax: (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (E) - 9 (L)
    ON (Door lock set to LOCK)
    Below 1 Ω
    7 (E) - 9 (L)
    7 (E) - 10 (UL)
    OFF (Free)
    10 kΩ or higher
    7 (E) - 10 (UL)
    ON (Door lock set to UNLOCK)
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for Regular Cab)
    C
    NG (for CrewMax)
    D



B
REPLACE FRONT DOOR LOCK MOTOR ASSEMBLY LH (Click here)

C
REPLACE FRONT DOOR LOCK MOTOR ASSEMBLY LH (Click here)

D
REPLACE FRONT DOOR LOCK MOTOR ASSEMBLY LH (Click here)
A


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK MOTOR LH - MAIN BODY ECU)

E177923E02

  1. Disconnect the N4 door lock connector.

  1. Disconnect the DD and J4 ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N4-9 (L) - DD-53 (L2)
    Always
    Below 1 Ω
    N4-10 (UL) - J4-10 (UL3)
    N4-7 (E) - Body ground
    N4-10 (UL) - Body ground
    Always
    10 kΩ or higher
    N4-9 (L) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU