Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. PLACE ROOF HEADLINING ASSEMBLY


B166622
  1. Place the roof headlining into the cabin as shown in the illustration.

    NOTICE:
    1. Place the headlining in the cabin so that it will not be damaged.
    2. Be careful not to damage the roof headlining when placing it in the cabin.



2. INSTALL BACK WINDOW ASSEMBLY
  1. for Fixed Type:
    Install the back window assembly (Click here).

  1. for Slide Type:
    Install the back window assembly (Click here).

  1. for Power Slide Type:
    Install the back window assembly (Click here).



3. INSTALL ROOF HEADLINING ASSEMBLY


  1. Attach the 4 clips to install the roof headlining.


    B232372E01



    B229072
  1. Connect the roof wire connector and attach the 3 clamps.



    B167283
  1. w/ EC Mirror:

    1. Connect the EC mirror connector.



4. INSTALL COAT HOOK


B168150

HINT:
Use the same procedure to install the coat hook on the other side.

  1. Install the clip and cap to the coat hook, as shown in the illustration.

  1. Install the coat hook.



5. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



6. INSTALL ASSIST GRIP SUB-ASSEMBLY


B165740
  1. Install the 2 clips and 2 covers to the assist grip, as shown in the illustration.

  1. Install the assist grip.



7. INSTALL VISOR HOLDER


B165713
  1. Install the visor holder with the screw.

    HINT:
    Use the same procedure to install the visor holder on the other side.



8. INSTALL VISOR ASSEMBLY LH


B165715
  1. Install the visor assembly LH with the 3 screws.



9. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



10. INSTALL VISOR BRACKET COVER LH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



11. INSTALL VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



12. INSTALL ROOM LIGHT ASSEMBLY (for Short Type Overhead Console Box)
  1. Connect the connector.

  1. Attach the 4 clips to install the room light.



  1. Attach the 4 claws to install the lens.


    B165837



13. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227101
  1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



14. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box .

  1. for Long Type:
    Install the roof console box .



15. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


B165833
  1. Pass the rear seat outer belt floor anchor through the quarter trim panel.

  1. Attach the 4 clips to install the front quarter trim panel.

  1. Install the 2 bolts.



    B165712
  1. Attach the claw to install the cover.



16. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



17. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165832
  1. Attach the 6 clips to install the lower quarter trim panel.



    B165831
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165830
  1. Attach the 2 claws to install the cover.



18. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B166614
  1. Slide the front shoulder belt anchor plate in the direction shown in the illustration and attach the 6 claws to install the plate.



20. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL CENTER PILLAR GARNISH LH
  1. Pass the front seat outer belt floor anchor through the center pillar garnish.

  1. Attach the claw to install the center pillar garnish.

  1. Install the 2 screws.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165826



22. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL LOWER CENTER PILLAR GARNISH LH


B165829
  1. Attach the 7 clips and 2 claws to install the lower center pillar garnish.



    B165828
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165827
  1. Attach the 2 claws to install the cover.



24. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



25. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



26. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



27. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the rear door opening trim weatherstrip.



28. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the rear door opening trim weatherstrip.



29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.



30. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.



31. INSTALL COWL SIDE TRIM BOARD LH


B165704
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.



32. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



33. INSTALL REAR DOOR SCUFF PLATE LH


B165842
  1. Attach the 6 claws and 2 clips to install the rear door scuff plate.



34. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



35. INSTALL FRONT DOOR SCUFF PLATE LH


B165841
  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



36. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



37. INSTALL REAR SEAT ASSEMBLY
  1. Install the rear seat assembly (Click here).



38. INSTALL FRONT SEAT ASSEMBLY (for Center Seat)
  1. Install the front seat assembly (Click here).



39. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Install the front seat assembly (Click here).



40. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Install the front seat assembly (Click here).



41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


42. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).