ROOF HEADLINING (for Double Cab) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat) |
Remove the front seat assembly (Click here).
| 4. REMOVE FRONT SEAT ASSEMBLY (for Power Seat) |
Remove the front seat assembly (Click here).
| 5. REMOVE FRONT SEAT ASSEMBLY (for Center Seat) |
Remove the front seat assembly (Click here).
| 6. REMOVE REAR SEAT ASSEMBLY |
Remove the rear seat assembly (Click here).
| 7. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Detach the 6 claws and 3 clips, and remove the front door scuff plate.
| 8. REMOVE FRONT DOOR SCUFF PLATE RH |
| 9. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Detach the 6 claws and 2 clips, and remove the rear door scuff plate.
| 10. REMOVE REAR DOOR SCUFF PLATE RH |
| 11. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 12. REMOVE COWL SIDE TRIM BOARD RH |
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the front door opening trim weatherstrip.
| 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Remove the front door opening trim weatherstrip.
| 15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the rear door opening trim weatherstrip.
| 16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Remove the rear door opening trim weatherstrip.
| 17. REMOVE FRONT PILLAR GARNISH LH |
Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Detach the claw and remove the front pillar garnish.

![]() |
Protect the curtain shield airbag.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 18. REMOVE FRONT PILLAR GARNISH RH |
| 19. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Detach the 2 claws and remove the cover.
![]() |
Loosen the bolt and disconnect the outer lap belt anchor.
![]() |
Detach the 7 clips and 2 claws, and remove the lower center pillar garnish.
| 20. REMOVE LOWER CENTER PILLAR GARNISH RH |
| 21. REMOVE CENTER PILLAR GARNISH LH |
Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Remove the 2 screws.
Detach the claw.
Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

| 22. REMOVE CENTER PILLAR GARNISH RH |
| 23. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
![]() |
Detach the 6 claws of the front shoulder belt anchor plate, and slide the plate in the direction of the arrow to remove it.
| 24. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH |
| 25. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH |
![]() |
Detach the 2 claws and remove the cover.
![]() |
Loosen the bolt and disconnect the outer lap belt anchor.
![]() |
Detach the 6 clips and remove the lower quarter trim panel.
| 26. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH |
| 27. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
![]() |
Using a screwdriver, detach the claw and remove the cover.
![]() |
Remove the 2 bolts.
Detach the 4 clips.
Pass the rear seat outer belt floor anchor through the quarter trim panel, and remove the front quarter trim panel.
| 28. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
| 29. REMOVE ROOF CONSOLE BOX ASSEMBLY |
for Short Type:
Remove the roof console box .
for Long Type:
Remove the roof console box .
| 30. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to detach the 2 claws from the roof headlining, and then detach the 2 claws of the inner rear view mirror stay holder cover from the mirror and remove the inner rear view mirror stay holder cover.
| 31. REMOVE ROOM LIGHT ASSEMBLY (for Short Type Overhead Console Box) |
Using a screwdriver, detach the 4 claws and remove the lens.
Detach the 4 clips.
Disconnect the connector and then remove the room light.

| 32. REMOVE VISOR BRACKET COVER LH |
![]() |
Using a moulding remover, detach the 4 claws and remove the visor bracket cover.
| 33. REMOVE VISOR BRACKET COVER RH |
| 34. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 3 screws and visor assembly LH.
| 35. REMOVE VISOR ASSEMBLY RH |
| 36. REMOVE VISOR HOLDER |
![]() |
Remove the screw and visor holder.
| 37. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
Detach the 2 clips and remove the assist grip.
| 38. REMOVE ASSIST GRIP PLUG |
![]() |
Insert a screwdriver into the service notch and break off the cap.
Detach the clip and remove the assist grip plug.
| 39. REMOVE COAT HOOK |
![]() |
Using a screwdriver, detach the 2 claws and remove the coat hook cap.
Detach the clip and remove the coat hook.
| 40. REMOVE ROOF HEADLINING ASSEMBLY |
![]() |
w/ EC Mirror:
Disconnect the EC mirror connector.
![]() |
Disconnect the roof wire connector and detach the 3 clamps from the front pillar.
Detach the 4 clips and remove the roof headlining.

| 41. REMOVE BACK WINDOW ASSEMBLY |
for Fixed Type:
Remove the back window assembly (Click here).
for Slide Type:
Remove the back window assembly (Click here).
for Power Slide Type:
Remove the back window assembly (Click here).
| 42. TAKE OUT ROOF HEADLINING ASSEMBLY |
![]() |
Take out the roof headlining from the cabin as shown in the illustration.