Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Fold Down Seat Type)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Fold Down Seat Type) > REMOVAL

for Preparation Click here


CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. If the side airbag was deployed, replace the front seat airbag assembly, front seat back cover and front seat frame with adjuster assembly with the necessary parts in accordance with the extent of the collision damage.
  3. Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT SEAT ASSEMBLY RH
  1. Remove the front seat assembly RH (Click here).



4. REMOVE FRONT SEAT HEADREST ASSEMBLY RH


5. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH


B165802
  1. Lift the reclining adjuster release handle.

  1. Using a screwdriver, detach the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE FRONT SEAT CUSHION SHIELD RH


    B165523E01
  1. Remove the hog rings and rubber bands of the seatback cover from the seat frame.



    B165809E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.



7. REMOVE INNER FRONT SEAT CUSHION SHIELD RH


B165805E01
  1. Remove the screw.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.



8. REMOVE FRONT SEATBACK LOCK HANDLE LH


B165544
  1. Using a screwdriver, remove the seatback lock handle as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT SEATBACK LOCK HANDLE RH


B166548
  1. Using a screwdriver, remove the seatback lock handle as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.



10. REMOVE FRONT SEATBACK SHIELD LH


B165545
  1. Remove the screw.

  1. Detach the 2 claws and remove the seatback shield.



11. REMOVE FRONT SEATBACK SHIELD RH
  1. Remove the screw.

  1. Detach the 2 claws and remove the seatback shield.



    B165546
  1. Disconnect the airbag wire harness from the seatback shield.



12. REMOVE FRONT SEATBACK ASSEMBLY RH


    B255629
  1. Disconnect the 3 airbag wire harness clamps from under the seat.



    B165548
  1. Remove the 4 bolts and seatback.



13. REMOVE FRONT SEATBACK BOARD


B165549E01
  1. Detach the 2 clips and 2 hooks, and then remove the seatback board.



14. REMOVE FRONT SEATBACK LOCK SUB-ASSEMBLY LH


B165550
  1. Remove the 2 bolts and seatback lock.



15. REMOVE FRONT SEATBACK LOCK SUB-ASSEMBLY RH


B166555
  1. Remove the 2 bolts and seatback lock.



16. REMOVE FRONT SEATBACK COVER WITH PAD RH


    B165552
  1. Remove the nut and disconnect the seatback cover bracket from the seatback spring.



    B165553E01
  1. Remove the hog rings.



    B165554E01
  1. Remove the hog rings.



    B165529
  1. Detach the 4 claws and remove the 2 headrest supports.

  1. Remove the seatback cover with pad.



17. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B255630
  1. Disconnect the clamp.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.