Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (except Fold Down Seat Type)

FRONT SEAT SIDE AIRBAG ASSEMBLY (except Fold Down Seat Type) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
Use the same procedures for the LH side and RH side.



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B255936
  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the 2 clamps.



    B255935
  1. Connect the 3 wire harness clamps to under the seat.



2. INSTALL FRONT SEATBACK COVER WITH PAD LH (for Manual Seat)
  1. Install the seatback cover with pad to the seatback frame.



    B165534E02
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B165533
  1. Connect the seatback cover bracket to the seat frame and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



    B165531E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165530E02
  1. Attach the hook.



3. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Manual Seat)


4. INSTALL INNER FRONT SEAT CUSHION SHIELD LH (for Manual Seat)


B166410E01
  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the screw.



5. INSTALL FRONT SEAT CUSHION SHIELD LH (for Manual Seat)


B166409E01
  1. w/ Lumbar Support Adjuster:
    Connect the switch connector.

  1. Attach the 3 claws in the order shown in the illustration, and install the cushion shield.

  1. Install the 2 screws.



    B165523E03
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



6. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)


B165804
  1. Attach the claw to install the reclining adjuster release handle.



7. INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for 8 Way Seat)
  1. Install the snap ring to the vertical seat adjuster knob.



    B166938
  1. Install the vertical seat adjuster knob to the front seat.



8. INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat)


    B165520
  1. Install the vertical adjusting handle with the 2 screws.



    B165519
  1. Attach the 2 claws to install the vertical adjusting handle cap.



9. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Install the front seat assembly LH (Click here).



10. INSTALL FRONT SEATBACK COVER WITH PAD LH (for Power Seat)
  1. Install the seatback cover with pad to the seatback frame.



    B165534E04
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B165533
  1. Install the seatback cover bracket to the seat frame with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



    B167102E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seat frame.



    B167101E02
  1. Attach the hook.



11. INSTALL INNER FRONT SEAT CUSHION SHIELD LH (for Power Seat)


B166948
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



12. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Power Seat)


B166599E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.

  1. Driver Side:

    1. Connect the 2 connectors and attach the 4 clamps.

  1. Passenger Side:
    Connect the connector and attach the clamp.



13. INSTALL FRONT SEAT CUSHION SHIELD LH (for Power Seat)


B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B166944E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



14. INSTALL RECLINING POWER SEAT SWITCH KNOB LH (for Power Seat)


B167192
  1. Attach the 2 claws to install the knob.



15. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH (for Power Seat)


B167193
  1. Attach the 2 claws to install the knob.



16. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Install the front seat assembly LH (Click here).



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).