Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SIDE AIRBAG SENSOR (for Double Cab)

SIDE AIRBAG SENSOR (for Double Cab) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SIDE AIRBAG SENSOR
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Install the door airbag sensor with the screw.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the door airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the door airbag sensor.

  1. Connect the connector.



2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Front Side)


    B165684E03
  1. Connect the 2 cables to the inside handle.

  1. Connect the connector.

  1. Attach the inside handle's knob to the door trim board.



    B166215E01
  1. Attach the 9 clips to install the door trim board.

  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw.

  1. Install the clip.



3. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH (for Front Side)


    B168274E01
  1. Attach the 3 clips to install the front door lower frame bracket garnish.



4. INSTALL FRONT ARMREST BASE PANEL UPPER LH (for Front Side)


    B166211E01
  1. Connect the connectors.

  1. Attach the 2 clips to install the front armrest upper base panel.



5. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (for Front Side)


    B165648E03
  1. Attach the 4 claws to install the bezel plug.



6. INSTALL REAR SIDE AIRBAG SENSOR


    B166508
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Install the side airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the side airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the side airbag sensor.

  1. Connect the connector.



7. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH (for Rear Side)


B165832
  1. Attach the 6 clips to install the lower quarter trim panel.



    B165831
  1. Connect the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165830
  1. Attach the 2 claws to install the cover.



8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Rear Side)


9. INSTALL REAR DOOR SCUFF PLATE LH (for Rear Side)


B165842
  1. Attach the 6 claws and 2 clips to install the rear door scuff plate.



10. INSTALL REAR SEAT ASSEMBLY (for Rear Side)
  1. Install the rear seat assembly (Click here).



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).