Home › BODY › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY (for Power Seat)

FRONT POWER SEAT MOTOR ASSEMBLY (for Power Seat) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SEAT WIRE LH


2. INSTALL SEAT POSITION AIRBAG SENSOR


    C108775E04
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    Some systems need to be initialized after the cable is reconnected (Click here).



    C107067E04
  1. Using a feeler gauge 1.0 mm (0.0393 in.), install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Using a T30 "TORX" socket wrench, install the seat position sensor with the screw.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector.

  1. Install the seat slide position sensor protector to the seat position sensor.



3. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


B167116
  1. Attach the claw to install the ECU.

  1. Connect the 2 ECU connectors.



4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


B167111
  1. Attach the claw to install the seat heater control.

  1. Attach the clamp and connect the seat heater control connector.



5. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support Adjuster)


    B167110
  1. Attach the 3 claws to install the bush.



    B167109
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B167105E02
  1. w/o Climate Control Seat System:

    1. Attach the 6 hooks to install the seatback spring.

    2. Install the 2 springs.



    B194042E02
  1. w/ Climate Control Seat System:

    1. Attach the 4 hooks to install the seatback spring.

    2. Install the 4 springs.



6. INSTALL LOWER FRONT SEAT CUSHION SHIELD RH


B167108E02
  1. Attach the hook to install the cushion shield.

  1. Install the screw.



7. INSTALL LOWER FRONT SEAT CUSHION SHIELD LH
  1. Attach the hook to install the cushion shield.

  1. Install the screw.



8. INSTALL FRONT SEATBACK SHIELD RH


B191027
  1. Attach the claw to install the seatback shield.

  1. Install the 2 screws.

  1. Attach the wire harness clamp.



9. INSTALL FRONT SEATBACK SHIELD LH


B167107
  1. Attach the claw to install the seatback shield.

  1. Install the 2 screws.



10. INSTALL RECLINING ADJUSTER INSIDE COVER RH


B167106
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



11. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



12. INSTALL FRONT SEATBACK COVER WITH PAD LH
  1. Install the seatback cover with pad to the seatback frame.



    B165534E04
  1. Using hog ring pliers, install new hog rings to the seat frame.



    B165529
  1. Attach the 4 claws to install the 2 headrest supports.



    B165533
  1. Install the seatback cover bracket to the seat frame with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.



    B167102E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install new hog rings to the seat frame.



    B167101E02
  1. Attach the hook.



13. INSTALL FRONT SEAT CUSHION COVER WITH PAD LH


    B167115E02
  1. w/o Leg Support Adjustment Switch:

    1. Attach the hooks to install the seat cushion cover with pad.

    2. Using hog ring pliers, install new hog rings.

    3. Bend the 2 seat frame claws downward.



    B167190
  1. w/ Leg Support Adjustment Switch:

    1. Install the seat cushion cover with pad to the seat frame.

    2. Install the seat cushion cover wire.



    3. B166950E02
    4. Using hog ring pliers, install new hog rings and attach the hooks.

      HINT:
      When installing the leg support hog rings, press the seat cushion cover with pad against the seat frame.



    B227991
  1. Attach the wire harness clamp.



  1. w/ Seat Heater System or Climate Control Seat System:



      B179848
    1. Connect the seat heater control connector and attach the 2 wire harness clamps.



    2. B179847
    3. Connect the seat heater connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



14. INSTALL FRONT POWER SEAT SWITCH LH


B166949
  1. Install the switch with the 3 screws.

  1. Connect the 2 switch connectors.

  1. w/o Seat Position Memory System:
    Connect the switch connector.



15. INSTALL INNER FRONT SEAT CUSHION SHIELD LH


B166948
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



16. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


B166599E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.

  1. Driver Side:

    1. Connect the 2 connectors and attach the 4 clamps.

  1. Passenger Side:
    Connect the connector and attach the clamp.



17. INSTALL FRONT SEAT CUSHION SHIELD LH


B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B166944E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.



18. INSTALL RECLINING POWER SEAT SWITCH KNOB LH


B167192
  1. Attach the 2 claws to install the knob.



19. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B167193
  1. Attach the 2 claws to install the knob.



20. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat (Click here).