Home › ENGINE ยท 1UR-FE › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL THROTTLE BODY ASSEMBLY


    A218983E01
  1. Align the protrusion of a new gasket with the groove of the intake manifold, and install the gasket.



    A215292
  1. Install the throttle body with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR


    A215299
  1. Install a new O-ring to the manifold absolute pressure sensor.



    A215298
  1. Install the manifold absolute pressure sensor with the screw.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the manifold absolute pressure sensor connector.



3. INSTALL UNION TO CONNECTOR TUBE HOSE ASSEMBLY


    A215295
  1. Install the union to connector tube hose to the intake manifold.

  1. Install the 2 bolts and attach the hose clamp.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 wire harness brackets with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL PURGE VSV


    A215294
  1. Connect the purge line hose to the intake manifold.

  1. Install the purge VSV to the intake manifold with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



5. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Install the vacuum switching valve to the intake manifold with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 vacuum hoses to the vacuum switching valve.



6. INSTALL STUD BOLT


    A216133
  1. Using an E5 "TORX" socket wrench, install the 2 stud bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL V-BANK COVER PIN


    A215291
  1. Install the pin to the intake manifold.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL V-BANK COVER BRACKET


    A215290
  1. Install the bracket with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL FUEL TUBE SUB-ASSEMBLY


    A215303
  1. Install the fuel tube to the intake manifold with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



10. INSTALL INTAKE MANIFOLD


    A215297
  1. Place 2 new gaskets on the intake manifold.

  1. Place the intake manifold on the cylinder head.



    A215289
  1. Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A214312
  1. Connect the fuel tube to the fuel delivery pipe LH (Click here).



    A214311
  1. Connect the fuel tube to the fuel delivery pipe RH (Click here).



    A216804
  1. Attach the 4 clamps to the fuel tube as shown in the illustration.



    A215285
  1. Attach the 3 wire harness clamps to the 3 wire harness brackets.

  1. Connect the wire harness to the wire harness bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A215288
  1. Connect the vacuum hose.



    A215287
  1. Connect the purge VSV connector.

  1. Connect the purge line hose to the purge VSV.

  1. Connect the vacuum switching valve connector (for ACIS).



    A215281
  1. Connect the No. 1 ventilation hose.

  1. Connect the No. 4 water by-pass hose.

  1. Connect the throttle body connector.



11. INSTALL VENTILATION HOSE ASSEMBLY


    A215286
  1. Install the ventilation hose with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.



12. INSTALL AIR TUBE SUB-ASSEMBLY LH


    A215284
  1. Connect the air hose to the air switching valve LH, and install the air tube LH with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the vacuum sensor connector and clamp.



    A217630E01
  1. Connect the air tube LH to the water inlet housing with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the air hose.

  1. Connect the 2 wire harness clamps.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



    A215880E01
  1. Connect the water by-pass hose and 2 connectors.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



13. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


  1. Install the outer panel with the 7 bolts.


    A215877

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the washer hose.

  1. Connect the 2 wire harness clamps.



14. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Install the front wiper motor and link (Click here).



15. INSTALL EGR VALVE ASSEMBLY
  1. Install the EGR valve (Click here).



16. CHECK FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch ON.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.