Home › ENGINE ยท 3UR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. REMOVE ENGINE STAND


    A163784E01
  1. Install the 2 engine hangers with the 2 bolts as shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    Item
    Part No.
    Engine hanger
    12281-38150
    Bolt
    90119-A0166

  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the bolts and engine assembly from the engine stand.



2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A162119E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162115E01
  1. Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



3. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



4. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine assembly into the engine compartment.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Attach the engine mounting insulators to the vehicle.



    A163780E01
  1. Install the 4 engine mounting insulator bolts.

    Torque:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }

  1. Remove the 2 bolts and 2 engine hangers.



5. INSTALL NO. 1 WATER BY-PASS PIPE


    A163785
  1. Connect the hose and install the water by-pass pipe with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



6. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A163778E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  

  1. Install the crankshaft angle sensor plate, drive gear and rear drive plate spacer to the crankshaft.



    A163779E01
  1. Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Do not reuse the flywheel installation bolts.
    2. Do not strike or damage the flywheel installation bolts. Be sure to handle them carefully.



    A149106E01
  1. Mark the upside of each flywheel installation bolt with paint.

  1. Tighten the flywheel installation bolts another 90° as shown.

  1. Check that the painted marks are now at a 90° angle to the upside.



7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



8. INSTALL STARTER ASSEMBLY


    A163323
  1. Install the flywheel housing side cover.

  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Attach the 2 wire harness clamps.



9. INSTALL STARTER COVER
  1. Install the starter cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



10. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162117E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162754E01
  1. Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



11. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



12. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.



    A164434E01
  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.



13. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 5 clips.



14. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the fender apron seal with the 6 clips.



15. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
  1. Install the front propeller shaft (Click here).



16. INSTALL PROPELLER SHAFT ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



17. INSTALL EXHAUST PIPE ASSEMBLY
  1. for Regular Cab Standard Deck:
    Refer to the following procedures (Click here).

  1. except Regular Cab Standard Deck:
    Refer to the following procedures (Click here).



18. INSTALL GENERATOR ASSEMBLY


    A156406
  1. Install the generator with the 3 bolts and nut.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



    A156405
  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Install the harness bracket to the generator with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



19. CONNECT VANE PUMP ASSEMBLY


A163333E01

HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.



    A163289
  1. Connect the vane pump to the timing chain cover with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



20. CONNECT COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.



21. CONNECT WIRE HARNESS AND HOSE


    A163790
  1. Connect the 2 connectors and 2 clips to the engine room junction block.

  1. Install the engine wire with the nut. Then connect the 2 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 air injection control driver connectors.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the cable to the positive (+) battery terminal.

  1. Install the wire to the positive (+) battery cable with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A163791
  1. Connect the 2 air injection system hoses.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 air pump connectors and install the connector bracket with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    A160782E01
  1. Connect the 4 connectors to the connector holder block.



    A163788
  1. Connect the heater hoses.

  1. Connect the ECM connector and clamp.

    HINT:
    Refer to the following procedures to connect the ECM connector .



    A163789
  1. Connect the union to check valve hose.

  1. Connect the purge line hose.



22. CONNECT FUEL MAIN AND RETURN HOSE


    A184550
  1. Connect the fuel main and return hoses (Click here).

  1. Install the fuel pipe clamp.



23. INSTALL RADIATOR ASSEMBLY


    A151752
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



24. INSTALL FAN SHROUD
  1. Install the fan pulley to the fan bracket.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A151820
  1. Attach the shroud's claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the upper radiator tank.

  1. Install the fan and generator V-belt.



    A151842
  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



25. INSTALL FAN & GENERATOR V BELT


    A163771E01
  1. Set the V belt onto every part.

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly set to each pulley.



    A174124E01
  1. After installing the belt, check that it fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



26. INSTALL RADIATOR SIDE DEFLECTOR LH


    A215584
  1. Install the deflector with the 6 clips.

  1. Connect the wire harness clamp.



27. INSTALL RADIATOR SIDE DEFLECTOR RH


    A232101E01
  1. Install the deflector with the 6 clips.



28. INSTALL OUTLET RADIATOR HOSE


29. INSTALL INLET RADIATOR HOSE


30. INSTALL AIR CLEANER ASSEMBLY


    A156197E01
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element onto the air cleaner case.



    A162105E01
  1. Install the air cleaner cap.

    1. Fasten the 4 hook clamps.

    2. Connect the MAF meter connector.

    3. Attach the wire harness clamp.



31. INSTALL AIR CLEANER HOSE ASSEMBLY


    A162102
  1. Install the air cleaner hose with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the ventilation hose.



32. ADD ENGINE OIL
  1. Add fresh oil.

    Standard oil grade:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    0W-20

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)

  1. Install the oil filler cap.



33. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard capacity: 
    Item
    Specified Condition
    w/ Trailer Towing System
    13.0 liters (13.7 US qts, 11.4 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


35. INSPECT FOR OIL LEAK
  1. Inspect for engine oil leak .



36. INSPECT FOR COOLANT LEAK


A161766

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



37. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


38. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



39. INSPECT SHIFT LEVER POSITION
  1. for Column shift:
    Refer to the following procedures .

  1. for Floor shift:
    Refer to the following procedures .



40. INSTALL V-BANK COVER SUB-ASSEMBLY


    A165576E02
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



41. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


  1. Install the outer panel with the 7 bolts.


    A151796

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 washer hoses.



42. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Install the windshield wiper motor (Click here).



43. INSTALL HOOD SUB-ASSEMBLY


    A160840
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

    NOTICE:
    Install the hood support while supporting the hood by hand.

  1. Attach the hood support clips.

    NOTICE:
    Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



44. ADJUST HOOD SUB-ASSEMBLY


    B166027
  1. Adjust the hood's position.

    1. Loosen the hood's 4 hinge bolts.

    2. Move the hood and adjust the clearance between the hood and front fender.

    3. Tighten the hood's 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    4. B166028
    5. Adjust the cushion rubber so that the height of the hood and fender are aligned.

      HINT:
      Raise or lower the hood's front end by turning the cushion rubber.



  1. Adjust the hood lock.



      B166029
    1. Using a screwdriver, remove the hood lock nut cap as shown in the illustration.

      HINT:
      Tape the screwdriver tip before use.



    2. B166030
    3. Loosen the 2 bolts and hood lock nut.

    4. Adjust the hood lock position so that the striker can enter it smoothly.

    5. Tighten the bolts and nut after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    6. Install a new cap.



45. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



46. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Start the engine and idle it.

    3. Push the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.

      HINT:
      Refer to the Techstream operator's manual for further details.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch OFF)

    5. Disconnect the Techstream from the DLC3.



    A160842
  1. When not using the Techstream:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.



    2. H102392E79
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C before connecting the terminals.



    4. A160843
    5. Using the timing light, check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch OFF)

    6. Remove SST from the DLC3.

    7. Check the ignition timing.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch OFF)

    8. Disconnect the timing light from the engine.



47. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the Techstream.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Push the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      HINT:
      Refer to the Techstream operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the Techstream from the DLC3.



    H102392E88
  1. When not using the Techstream:

    1. Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C before connecting the probe.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer probe from the DLC3.



48. INSPECT CO/HC

HINT:
This check is used only to determine whether or not the idle CO/ HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.



    A150141E01
  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter



49. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



50. CHECK ENGINE COOLANT LEVEL


    A151850E05
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.