DTC P0401 Exhaust Gas Recirculation Flow Insufficient Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0401 | Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation (2 trip detection logic) |
|
| Related DTC | P0401: EGR valve high flow rate / low flow rate |
| Required sensors/Components (Main) | EGR valve assembly, manifold absolute pressure sensor |
| Required sensors/Components (Related) | Engine coolant temperature sensor, vehicle speed sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 3 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| Monitor runs whenever following DTCs are not present | None |
| Time after engine started | 3 seconds or more |
| Time after engine fuel cut | 1 second or more |
| Engine speed | 1050 to 1800 rpm |
| Vehicle speed | 20 km/h (12.5 mph) or more |
| Engine speed change (per 65 msec.) | -40 to 10 rpm |
| Time after engine load becomes stable (Brake, lock-up) | More than 1 sec |
| Shift position | Except "P" or "N" range |
| Engine coolant temperature | 75°C (167°F) or more |
| Battery voltage | 11 V or more |
| Intake air temperature | -10°C (14°F) or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Manifold pressure change | Less than 1.8125 kPa (14 mmHg) |
| Engine speed | 1400 rpm |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Data List | Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test |
| Engine Speed | Idle becomes rough |
| MAP | Pressure rises |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0401) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0401 is output | A |
| DTC P0401 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | - | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
| OK | |
| 3.INSPECT EGR VALVE |
Confirm that there are no deposits on the EGR valve.
Confirm that the EGR valve is closed.
|
| ||||
|
| ||||
| 4.REPLACE EGR VALVE ASSEMBLY |
Replace the EGR valve assembly (Click here).
| NEXT | |
| 5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT) |
![]() |
Check for exhaust leaks at each connection point.
Check for cracks, damage and blockage of the pipes between the intake manifold converter and EGR valve assembly.
Check for blockage due to deposits in the EGR valve and pipes.
|
| ||||
| OK | |
| 6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY) |
![]() |
Check for exhaust leaks at each connection point.
Check for cracks, damage and blockage of the pipes between the exhaust manifold converter and EGR valve assembly.
Check for blockage due to deposits in the EGR valve and pipes.
|
| ||||
| OK | |
| 7.INSPECT EGR COOLER |
Check for blockage in the EGR cooler.
|
| ||||
| OK | |
| 8.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the MAP value.
| Switch Condition | Techstream Display |
| Ignition switch ON | 80 to 110 kPa (600 to 825 mmHg) |
Read the MAP value when racing the engine.
| Engine Condition | Techstream Display |
| Idling | 20 to 40 kPa (150 to 300 mmHg) |
|
| ||||
|
| ||||
| 9.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor (Click here).
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTC (Click here).
Turn the ignition switch off and wait for 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more.
Idle the engine for 30 seconds or more.
Drive the vehicle at 60 km/h (37 mph).
Perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0401.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||