SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, use the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer. |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 650 to 800 rpm: Idling | - |
| Calculate Load | Calculated load by ECM/ Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load/ Min.: 0%, Max.: 25700% | Actual vehicle load | - |
| MAF | Air flow rate from Mass Air Flow (MAF) meter/ Min.: 0 gm/sec., Max.: 655.35 gm/sec. | 3.4 to 6.2 gm/sec.: Idling | If value approximately 0.0 gm/sec.:
|
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| MAP | Intake manifold pressure/ Min.: 0 kPa, Max.: 255 kPa |
| - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 215°C | 80 to 100°C (176 to 212°F): After warming up | If value -40°C (-40°F), sensor circuit open. If value 140°C (284°F), sensor circuit shorted. |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature | If value -40°C (-40°F), sensor circuit open. If value 140°C (284°F), sensor circuit shorted. |
| Engine Run Time | Engine run time/ Min.: 0 s, Max.: 65535 s | Time after engine start | Service data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 119.3°C | Engine coolant temperature when engine started | Service data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 119.3°C | Intake air temperature when engine started | Service data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | - |
| Accelerator Position | Accelerator pedal position/ Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal is released 52 to 90%: Accelerator pedal is fully depressed | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 24 to 40%: Accelerator pedal is released 68 to 95%: Accelerator pedal is fully depressed | - |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Accelerator pedal is released 2.6 to 4.5 V: Accelerator pedal is fully depressed | - |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: Accelerator pedal is released 3.4 to 4.75 V: Accelerator pedal is fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle/ ON or OFF | ON: Idling | - |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2/ Min.: 0 deg, Max.: 124.5 deg | - | ETCS service data |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| The calculated value based on VTA1. |
| Throttl Sensor #2 Volt % | Throttle sensor position #2/ Min.: 0%, Max.: 100% |
| The calculated value based on VTA2. |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed | - |
| System Guard | System guard/ ON or OFF | - | ETCS service data |
| Open Side Malfunction | Open side malfunction/ ON or OFF | - | ETCS service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/ ON or OFF | ON: Accelerator pedal released OFF: Accelerator pedal depressed | - |
| Throttle Require Position | Throttle requirement position/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position* | Throttle sensor position/ Min.: 0%, Max.: 100% |
| Recognition value of throttle opening angle for ECM |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle position sensor No. 1/ Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | ETCS service data |
| Throttle Sens Open Pos #2 | Throttle position sensor No. 2/ Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | ETCS service data |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | ETCS service data |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 10 to 22%: Idling | ETCS service data |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | ETCS service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | ETCS service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value)/ Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| +BM Voltage | +BM voltage/ Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON and system normal | ETCS service data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | ETCS service data |
| Throttle Position | Throttle valve opening angle/ Min.: 0 deg, Max.: 499.99 deg | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Flow | Flow rate calculated using information from each sensor/ Min.: 0 L/s, Max.: 79.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Position | Requested opening amount calculated using ISC control/ Min.: 0 deg, Max.: 499.99 deg | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Feedback Value | ISC feedback compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| ISC Learning Value | ISC learned compensation amount/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| PS Feedback Val | Compensation flow rate according to power steering load/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Low Revolution Control | Low engine speed control operation state/ ON or OFF | - | For use when engine stall, starting problems or rough idle is present. |
| N Range Status | Shift lever N status/ ON or OFF | - | For use when engine stall, starting problems or rough idle is present. |
| Eng Stall Control FB Flow | Intake air compensation flow rate/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Deposit Loss Flow | Flow loss due to deposits/ Min.: -40 L/s, Max.: 39.99 L/s | - | For use when engine stall, starting problems or rough idle is present. |
| Fuel Pump Duty | Fuel pump duty/ Min.: 0%, Max.: 399.0% | - | - |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 μs, Max.: 65535 μs | 1400 to 4000 μs: Idling | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.047 ml | 0 to 0.5 ml | Quantity of fuel injection volume for 10 times |
| Vacuum Pump | Key-off EVAP system pump status/ ON or OFF | - | - |
| Current Fuel Type | Status of the current fuel type | Gasoline/petrol | - |
| EVAP (Purge) VSV | Purge VSV control duty/ Min.: 0%, Max.: 100% | 0 to 100%: During idling | Order signal from ECM |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | - |
| Purge Density Learn Value | Learning value of purge density/ Min.: -200, Max.: 199.993 | Idling: -40 to 0 | Service data |
| Vapor Pressure Pump | Vapor pressure/ Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg) | Approximately 100 kPa (750 mmHg): Ignition switch ON | EVAP system pressure monitored by canister pressure sensor. |
| Vapor pressure (Calculated) | Calculated EVAP system pressure/ Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg) | Approximately 100 kPa (750 mmHg): Ignition switch ON | - |
| EVAP System Vent Valve | Key-off EVAP system vent valve status/ ON or OFF | - | - |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | - |
| Purge Cut VSV Duty | Purge cut VSV duty/ Min.: 0%, Max.: 399.9% | - | - |
| Target Air-Fuel Ratio | Target Air fuel ratio/ Min.: 0, Max.: 1.99 | 0.8 to 1.2: During idling | - |
| AF Lambda B1S1 | Output air fuel ratio associated with the Bank 1 Sensor 1/ Min.: 0, Max.: 1.99 |
| - |
| AF Lambda B2S1 | Output air fuel ratio associated with the Bank 2 Sensor 1/ Min.: 0, Max.: 1.99 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/ Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Voltage B2S1 | Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/ Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor current (for Bank 1 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor. |
| AFS Current B2S1 | Air fuel ratio sensor current (for Bank 2 Sensor 1)/ Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor. |
| A/F Heater Duty #1 | A/F heater duty ratio (for Bank 1) Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| A/F Heater Duty #2 | A/F heater duty ratio (for Bank 2) Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving at 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S B2S2 | Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/ Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving at 70 km/h (44 mph) | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor. |
| O2S Impedance B1S2 | Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving approx. 10 min. in urban area |
| O2S Impedance B2S2 | Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/ Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | After driving approx. 10 min. in urban area |
| O2 Heater B1S2 | Heated oxygen sensor heater (for Bank 1 Sensor 2)/ Active or Not Act | - | - |
| O2 Heater B2S2 | Heated oxygen sensor heater (for Bank 2 Sensor 2)/ Active or Not Act | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current (for Bank 1 Sensor 2)/ Min.: 0 A, Max.: 4.9 A | - | - |
| O2 Heater Curr Val B2S2 | Heated oxygen sensor current (for Bank 2 Sensor 2)/ Min.: 0 A, Max.: 4.9 A | - | - |
| Short FT #1 | Short-term fuel trim of bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim of bank 1/ Min.: -100%, Max.: 99.2% | -20 to +20% |
|
| A/F Learn Value Idle #1 | Air fuel ratio learned value for idling (for Bank 1)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher). |
| A/F Learn Value Low #1 | Air fuel ratio learned value for low engine loads (for Bank 1)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #1 | Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #1 | Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #1 | Air fuel ratio learned value for high engine loads (for Bank 1)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #1 | Total fuel trim of bank 1/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Short FT #2 | Short-term fuel trim of bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% | This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim of bank 2/ Min.: -100%, Max.: 99.2% | -20 to +20% |
|
| A/F Learn Value Idle #2 | Air fuel ratio learned value for idling (for Bank 2)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher). |
| A/F Learn Value Low #2 | Air fuel ratio learned value for low engine loads (for Bank 2)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #2 | Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #2 | Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #2 | Air fuel ratio learned value for high engine loads (for Bank 2)/ Min.: -50%, Max.: 49.6% | -20 to +20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #2 | Total fuel trim of bank 2/ Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (Bank 1)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (Bank 2)/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up |
|
| Air pump pressure (Absolute) | Air pump pressure (absolute) for Bank 1/ Min.: 0 kPa, Max.: 65535 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open Close to atmospheric pressure: Air pump OFF, air switching valve closed | Refer to DTC P2431 (Click here) |
| Air Pump2 Pressure (Absolute) | Air pump pressure (absolute) for Bank 2/ Min.: 0 kPa, Max.: 65535 kPa | Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open Close to atmospheric pressure: Air pump OFF, air switching valve closed | Refer to DTC P2431 (Click here) |
| Air Pump Pulsation Pressure | Air pump pulsation pressure for Bank 1/ Min.: 0 kPa, Max.: 655.35 kPa | - | Cumulative pulsation pressure calculated by ECM (Click here) |
| Air Pump2 Pulsation Pressure | Air pump pulsation pressure for Bank 2/ Min.: 0 kPa, Max.: 655.35 kPa | - | Cumulative pulsation pressure calculated by ECM (Click here) |
| Secondary Air Control VSV | Secondary air injection system status/ ON or OFF | ON: Secondary air injection system operating | - |
| 2nd Air System Status | Secondary air system status/ ON or OFF | ON: Secondary air system operating | - |
| AI Test | AI operation prohibition/ READY or NOT RDY | READY | - |
| Subfreezing Conditions | Subfreezing conditions status/ ON or OFF | - | - |
| Air Pump Heater | Air pump heater status/ ON or OFF | - | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg., Max.: 63.5 deg. | BTDC 5 to 15°: Idling | - |
| Knock Feedback Value | Feedback value of knocking/ Min.: -1024 deg (CA), Max.: 1023.9 deg (CA) | -22 to 0 deg (CA): Driving at 70 km/h (44 mph) | Service data |
| Knock Correct Learn Value | Correction learning value of knocking/ Min.: -1024 deg (CA), Max.: 1023.9 deg (CA) | 0 to 25 deg (CA): Driving at 70 km/h (44 mph) | Service data |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #5 | Individual cylinder timing advance compensation amount (No. 5)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #6 | Individual cylinder timing advance compensation amount (No. 6)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #7 | Individual cylinder timing advance compensation amount (No. 7)/ Min.: 0° CA, Max.: 15.93° CA | - | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #8 | Individual cylinder timing advance compensation amount (No. 8)/ Min.: 0 deg (CA), Max.: 15.93 deg (CA) | - | For use when engine stall, starting problems or rough idle is present. |
| ACIS VSV | VSV status for ACIS control/ ON or OFF | - | Active Test support data |
| Target EGR Position | EGR valve target opening amount/ Min.: 0%, Max.: 100% | Changes according to engine speed and load: Driving | - |
| EGR Step Position | EGR step position/ Min.: 0 step, Max.: 255 step | Changes according to engine speed and load: Driving 0 step: Shift lever in D after racing the engine with shift lever in N | - |
| VVT Control Status #1 | Variable valve timing (VVT) control status (Bank 1)/ ON or OFF | - | - |
| VVT Control Status #2 | VVT control status (Bank 2)/ ON or OFF | - | - |
| VVT Advance Fail | VVT control failure status/ ON or OFF | ON: VVT control failure | - |
| VVT Aim Angle #1*2 | VVT target duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0%: Idling | VVT duty signal value during forced operation. |
| VVT Change Angle #1*2 | VVT change angle (Bank 1)/ Min.: 0 degFR, Max.: 639.9 degFR | 0 to 5 degFR: Idling | Displacement angle during forced operation. |
| VVT OCV Duty #1*2 | VVT OCV operation duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0%: Idling | Requested duty value for forced operation. |
| VVT Aim Angle #2*2 | VVT target duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0%: Idling | VVT duty signal value during forced operation. |
| VVT Change Angle #2*2 | VVT change angle (Bank 2)/ Min.: 0 degFR, Max.: 639.9 degFR | 0 to 5 degFR: Idling | Displacement angle during forced operation. |
| VVT OCV Duty #2*2 | VVT OCV operation duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0%: Idling | Requested duty value for forced operation. |
| VVT Ex Hold Lrn Val #1*2 | VVT exhaust hold duty ratio learning value (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #1*2 | VVT exhaust change angle (Bank 1)/ Min.: 0 degFR, Max.: 639.9 degFR | 0 to 40 degFR: Idling | Displacement angle during forced operation. |
| VVT Ex OCV Duty #1*2 | VVT exhaust OCV duty (Bank 1)/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | Requested duty value for forced operation. |
| VVT Ex Hold Lrn Val #2*2 | VVT exhaust hold duty ratio learning value (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 80%: Idling | - |
| VVT Ex Chg Angle #2*2 | VVT exhaust change angle (Bank 2)/ Min.: 0 degFR, Max.: 639.9 degFR | 0 to 40 degFR: Idling | Displacement angle during forced operation. |
| VVT Ex OCV Duty #2*2 | VVT exhaust OCV duty (Bank 2)/ Min.: 0%, Max.: 399.9% | 0 to 100%: Idling | Requested duty value for forced operation. |
| VN Turbo Type | VN turbo type/ Not Avl, Commo, Vacuum or CAN Com | Not Avl | - |
| Catalyst Temp B1S1 | Catalyst temperature (Bank 1, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S1 | Catalyst temperature (Bank 2, Sensor 1)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (Bank 1, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B2S2 | Catalyst temperature (Bank 2, Sensor 2)/ Min.: -40°C, Max.: 6513.5°C | - | - |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
| Starter Control | Starter switch status/ Open or Close | Open: Cranking | - |
| Power Steering Signal | Power steering switch signal/ ON or OFF | ON: Power steering operating | - |
| Starter Relay | Starter relay status/ ON or OFF | ON: Cranking | - |
| ACC Relay | ACC relay status/ ON or OFF | ON: Cranking | - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF | ON: P or N position | - |
| Transfer L4 | L4 status of the transfer/ ON or OFF | ON: 4WD control switch in 4L position | - |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal is depressed | - |
| A/C Signal | A/C switch status/ ON or OFF | ON: A/C ON | - |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| - |
| Fuel Cut Condition | Fuel cut condition/ ON or OFF | ON: Fuel cut operating | - |
| Immobiliser Communication | Immobiliser communication/ ON or OFF | ON: Normal | - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | Refer to Check Mode Procedure (Click here). |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - |
| AS Test Result | Check mode result for secondary air injection system/ Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor/ Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (Bank 1)/ Compl or Incmpl | - | - |
| OXS2 Test Result | Check mode result for heated oxygen sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #2 | Check mode result for air fuel ratio sensor (Bank 2)/ Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (Bank 1)/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor/ Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor/ Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor/ Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor/ Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor/ Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor/ Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR monitor/ Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR monitor/ Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor/ Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor/ Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor/ Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor/ Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor/ Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor/ Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor/ Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor/ Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor/ Compl or Incmpl | - | - |
| TC Terminal | TC terminal status/ ON or OFF | - | - |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | MIL ON run distance/ Min.: 0 km, Max.: 65535 km | Distance after DTC detected | - |
| Running Time from MIL ON | Running time from MIL ON/ Min.: 0 min, Max.: 65535 min | Running time after MIL turned ON | - |
| Time after DTC Cleared | Time after DTCs cleared/ Min.: 0 min, Max.: 65535 min | Time after DTCs were cleared | - |
| Distance from DTC Cleared | Distance after DTCs cleared/ Min.: 0 km, Max.: 65535 km | Driving distance after DTCs were cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycles after DTCs cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTCs cleared |
| Dist Batt Cable Disconnect | Distance after battery cable disconnected/ Min.: 0 km, Max.: 65535 km | Total distance vehicle driven after battery cable disconnected | - |
| IG OFF Elapsed Time | Time after ignition switch off/ Min.: 0 min, Max.: 655350 min | Cumulative time after ignition switch off | - |
| OBD Requirements | OBD requirement | OBD II (California ARB) | - |
| Number of Emission DTC | Emission related DTCs | - | Number of emission related DTCs |
| TC and TE1 | TC and CG (TE1) terminals of DLC3/ ON or OFF | - | - |
| Total Distance Traveled | Total distance traveled/ Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) | - | - |
| Ignition Trig. Count | Ignition counter/ Min.: 0, Max.: 65535 | 0 to 800 | - |
| Cylinder #1 Misfire Count to Cylinder #8 Misfire Count | Misfire count of cylinder 1 to 8/ Min.: 0, Max.: 255 | 0 | This item displayed only when idling engine. |
| All Cylinders Misfire Count | All cylinders misfire count/ Min.: 0, Max.: 255 | 0 to 35 | - |
| Multi Cylinders Misfire Count | Multiple cylinder misfire count/ Min.: 0, Max.: 65535 | 0 to 65535 | - |
| Misfire RPM | Engine RPM for first misfire range/ Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: Misfire 0 | - |
| Misfire Load | Engine load for first misfire range/ Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: Misfire 0 | - |
| Misfire Margin | Misfire monitoring/ Min.: -128%, Max.: 127% | -100 to 99.2% | Misfire detection margin |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention F/C/ Not Avl or Avail | Avail: Cat OT MF F/C available Not Avl: Cat OT MF F/C not available | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention F/C history/ ON or OFF | ON: Fuel cut operation history exists | - |
| Cat OT MF F/C Cylinder #1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #7 | Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Cat OT MF F/C Cylinder #8 | Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/ ON or OFF | ON: Fuel cut is operating | - |
| Engine Speed (Starter Off) | Engine speed when starter off/ Min.: 0 rpm, Max.: 51199 rpm | - | For use when engine stall, starting problems or rough idle is present. |
| Starter Count | Number of times starter turned on after ignition switch turned to ON/ Min.: 0, Max.: 255 | - | For use when engine stall, starting problems or rough idle is present. |
| Run Dist of Previous Trip | Distance driven during previous trip/ Min.: 0 km, Max.: 655.35 km | - | Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
| Engine Starting Time | Time elapsed after engine started (interval between ignition switch ON and off)/ Min.: 0 ms, Max.: 655350 ms | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Intake Temp | Intake air temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature)/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Ambient Temp for A/C | Ambient temperature for A/C/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip/ Min.: -40°C, Max.: 215°C | - | For use when engine stall, starting problems or rough idle is present. |
| Engine Start Hesitation | History of hesitation during engine start/ ON or OFF | - | - |
| Low Rev for Eng Start | History of low engine speed after engine start/ ON or OFF | - | - |
| Minimum Engine Speed | Minimum engine speed/ Min.: 0 rpm, Max.: 51199 rpm | - | For use when engine stall, starting problems or rough idle is present. |
| Power Steering Pressure | Power steering oil pressure/ Min.: 0 MPa, Max.: 25.599 MPa | - | - |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | Active Test support data |
| Brake Override System | Brake Override System Status/ ON or OFF | ON: Brake override system operation | - |
| Electric Cooling Fan Low | Electric fan motor operation status/ ON or OFF | ON: Cooling fan operated at low speed | - |
| Idle Fuel Cut | Fuel cut at idle/ ON or OFF | ON: Fuel cut operating | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm. |
| FC TAU | Fuel cut TAU: Fuel cut during very light load/ ON or OFF | ON: Fuel cut operating | The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete. |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut/ ON or OFF | - | - |
| Immobiliser Fuel Cut History | Status of the immobiliser fuel cut history/ ON or OFF | - | - |
| Vehicle Spec Signal 1 | Status of the Vehicle Spec Judge Signal 1/ OFF or ON | - | - |
| Electrical Load Signal 1 | Electrical load signal/ ON or OFF | - | - |
| Electrical Load Signal 2 | Electrical load signal/ ON or OFF | - | - |
| Cruise Cancel Signal | Status of the cruise cancel signal/ ON or OFF | - | - |
| Model Code | Model code | - | Used for identifying the model code: UPK5## |
| Engine Type | Engine type | - | Used for identifying the engine type: 1URFE |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | Used for identifying number of cylinders: 8 |
| Transmission Type | Transmission type | - | Used for identifying the transmission type: ECT 6th |
| Transmission Type 2 | Transmission type2 | NA | - |
| Destination | Destination | - | Used for identifying the destination: A (America) |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | Used for identifying the model year: 20## |
| System Identification | System Identification System identification | - | Identifying the engine system: Gasoline (gasoline engine). |
| Engine Speed of Cyl #1 | Engine RPM for cylinder No. 1/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #2 | Engine RPM for cylinder No. 2/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #3 | Engine RPM for cylinder No. 3/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #4 | Engine RPM for cylinder No. 4/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #5 | Engine RPM for cylinder No. 5/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #6 | Engine RPM for cylinder No. 6/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #7 | Engine RPM for cylinder No. 7/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Engine Speed of Cyl #8 | Engine RPM for cylinder No. 8/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| Av Engine Speed of All Cyl | Engine RPM for all cylinders/ Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression is performed using Active Test. |
| A/F Sensor Determination (worst value) #1 | Worst judgment value of air fuel ratio sensor output (bank 1)/ Min.: -1, Max.: 0.99 | 0.00 | - |
| A/F Sensor Determination (worst value) #2 | Worst judgment value of air fuel ratio sensor output (bank 2)/ Min.: -1, Max.: 0.99 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #1 | Worst value of average engine speed fluctuation (cylinder No. 1)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #2 | Worst value of average engine speed fluctuation (cylinder No. 2)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #3 | Worst value of average engine speed fluctuation (cylinder No. 3)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #4 | Worst value of average engine speed fluctuation (cylinder No. 4)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #5 | Worst value of average engine speed fluctuation (cylinder No. 5)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #6 | Worst value of average engine speed fluctuation (cylinder No. 6)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #7 | Worst value of average engine speed fluctuation (cylinder No. 7)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| Engine Speed Fluctuation Avg (worst value) #8 | Worst value of average engine speed fluctuation (cylinder No. 8)/ Min.: 0, Max.: 2.55 | 0.00 | - |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | Lock-up is:
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Overdrive Cut Switch #1 | Overdrive cut signal for cruise control/ ON or OFF | - | - |
| Shift SW Status (P Range) | Park/Neutral Position switch status (P Range)/ ON or OFF | Shift lever is:
| When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect |
| Shift SW Status (R Range) | Park/Neutral Position switch status (R Range)/ ON or OFF | Shift lever is:
| When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/Neutral Position switch status (N Range)/ ON or OFF | Shift lever is:
| When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch switch or shift cable may be incorrect |
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported/ Unsupp or Supp | - | - |
| Shift SW Status (N,P Range) | Park/Neutral Position switch status/ ON or OFF | Shift lever is:
| When shift lever position displayed on Techstream differs from actual position, adjustment of park/ neutral position switch switch or shift cable may be incorrect |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF | Shift lever is:
| - |
| Shift SW Status (D Range) | Park/Neutral Position switch status (D Range)/ ON or OFF | Shift lever is:
| When shift lever position displayed on Techstream differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect |
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/ Min.: -40°C, Max.: 215°C |
| If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/ Min.: -40°C, Max.: 215°C |
| If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted |
| Lock Up | Lock-up/ ON or OFF | Lock-up is:
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th, 5th or 6th | Shift lever is:
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF | Shift solenoid SLT is:
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ ON or OFF | Shift solenoid SLU is:
| - |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% |
|
| Control the EGR Step Position | Open or close EGR valve | 0 to 110 steps |
|
| Activate the VSV for Secondary Air Control | Activate the Secondary Air Injection System | ON/OFF |
|
| Activate the VSV for Intake Control | Activate VSV for intake control | ON/OFF | - |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | - |
| Control the A/C Cut Signal | Control A/C cut signal | ON/OFF | - |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | This test is possible when the following conditions are met:
|
| Control the Fuel Pump Duty | Activate fuel pump | 25%/80% | This test is possible when the following conditions are met:
|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Prohibit the Catalyst OT Misfire prevent F/C | Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire | ON: Fuel cut is prohibited | Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less. |
| Activate the Starter Relay | Activate the starter relay | ON/OFF | Perform this test with the engine stopped. |
| Activate the ACC Cut Relay | Activate the ACC CUT relay | ON/OFF | Perform this test with the engine stopped. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: Throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: Throttle valve opens quickly | Same as above. |
| Control the VVT Linear (Bank 1) | Control Variable Valve Timing (VVT) [Bank 1] | -128 to 127% (This value added to present OCV control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn Oil Control Valve (OCV) on and off | ON/OFF |
|
| Control the VVT Linear (Bank 2) | Control Variable Valve Timing (VVT) [Bank 2] | -128 to 127% (This value added to present OCV control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 2) | Turn Oil Control Valve (OCV) on and off | ON/OFF |
|
| Control the VVT Exhaust Linear (Bank 1) | Control VVT (Bank 1) | -128 to 127% (This value added to present OCV control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT Exhaust Linear (Bank 2) | Control VVT (Bank 2) | -128 to 127% (This value added to present OCV control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Activate the Vacuum Pump | Activate leak detection pump (built into canister pump module) | ON/OFF | - |
| Activate the VSV for Vent Valve | Activate vent valve (built into canister pump module) | ON/OFF | - |
| Activate the Air Pump Heater | Activate air pump heater | ON/OFF |
|
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #8) injection fuel cut | #1/#2/#3/#4/#5/#6/#7/#8 ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Control the All Cylinders Fuel Cut | All cylinder fuel cut | ON/OFF | Test possible while vehicle stopped and engine idling*1. |
| Check the Cylinder Compression*2 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stop in all cylinders. |
| SYSTEM CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the System Check by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Evaporative System Check (Automatic Mode) | Perform 6 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| Evaporative System Check (Manual Mode) | Perform 6 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|
| Secondary Air Injection Check (Automatic Mode) | Perform secondary air injection system operation automatically | With warm engine, ignition switch turned off once |
|
| Secondary Air Injection Check (Manual Mode) | Perform 7 operations in order to operate air injection system monitor manually | With warm engine, ignition switch turned off once |
|