SFI SYSTEM > EVAP System |
| DTC Code | Monitoring Item | See page |
| P043E | Reference orifice clogged (built into canister pump module) |
Click here
|
| P043F | Reference orifice high-flow (built into canister pump module) | |
| P0441 |
|
Click here
|
| P0451 |
|
Click here
|
| P0452 | Canister pressure sensor (built into canister pump module) voltage low | |
| P0453 | Canister pressure sensor (built into canister pump module) voltage high | |
| P0455 | EVAP gross leak |
Click here
|
| P0456 | EVAP small leak | |
| P2401 | Leak detection pump stuck OFF (built into canister pump module) |
Click here
|
| P2402 | Leak detection pump stuck ON (built into canister pump module) | |
| P2419 | Vent valve stuck closed (built into canister pump module) |
Click here
|
| P2420 | Vent valve stuck open (vent) (built into canister pump module) |
Click here
|
| P2610 | Soak timer (built into ECM) |
Click here
|


| *1 | Purge VSV | *2 | Purge Line Hose (to Intake Manifold) |
| *3 | Purge Line Hose (from Canister) | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Canister Assembly | *6 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) |
| *7 | Fuel Tank Cap Assembly | *8 | Fuel Tank |
| *9 | Purge Line | *10 | Bleeding Pipe |
| *a | Location of EVAP (Evaporative Emission) System | - | - |

| *1 | Canister Pump Module | *2 | Intake Manifold |
| *3 | Purge VSV | *4 | Throttle Valve |
| *5 | Canister Assembly | *6 | Cut-off Valve |
| *7 | Fuel Tank | *8 | Air Cleaner |
| *9 | ECM | *10 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) |
| *11 | Soak Timer | *12 | Roll-over Valve |
| *13 | Fuel Tank Cap Assembly | - | - |
| *a | EVAP System Circuit | - | - |
| Key-off monitor |
| Purge flow monitor |

| *1 | ECM | *2 | Soak Timer |
| *3 | Purge VSV (On) | *4 | Fuel Tank Cap Assembly |
| *5 | Canister Filter | *6 | Fuel Tank |
| *7 | Leak Detection Pump (Off) | *8 | Canister Pressure Sensor |
| *9 | Reference Orifice (0.02 Inches) | *10 | Vent Valve (Off) |
| *11 | Canister Pump Module | *12 | Canister Assembly |
| *a | EVAP Purge Flow | *b | to Intake Manifold |
| Component | Operation |
| Canister Assembly | Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank. |
| Cut-off valve | Located in fuel tank. Valve floats and closes when fuel tank 100% full. |
| Purge VSV (Vacuum Switching Valve) | Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake manifold controlled by purge VSV duty cycle (time current is flowing) (Open: ON; Closed: OFF). |
| Roll-over valve | Located in fuel tank. Valve closed by its own weight when vehicle overturns to prevent fuel from spilling out. |
| Soak timer | Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min.) after ignition switch turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours have elapsed, ECM activates (refer to fig. 3). |
| Canister pump module | Consists of (a) to (d) below. Canister pump module cannot be disassembled. |
| (a) Vent valve | Vents and closes EVAP system. When ECM turns valve ON, EVAP system closed. When ECM turns valve OFF, EVAP system vented. Negative pressure (vacuum) created in EVAP system to check for EVAP leaks by closing purge VSV, turning on vent valve (closed) and operating leak detection pump (refer to fig. 1). |
| (b) Canister pressure sensor | Indicates pressure as voltages. ECM supplies regulated 5 V to canister pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2). |
| (c) Leak detection pump | Creates negative pressure (vacuum) in EVAP system for leak check. |
| (d) Reference orifice | Has opening with 0.02-inch diameter. Vacuum produced through orifice by closing purge VSV, turning off vent valve and operating leak detection pump to monitor reference pressure. Reference pressure used to detect small leak of EVAP. |

| *1 | Canister | *2 | Reference Orifice (0.02 Inches) |
| *3 | Canister Pressure Sensor | - | - |
| *a | Canister Pump Module (fig. 1) | *b | Airflow |
| *c | Condition: Purge Flow | *d | Condition: Leak Check |
| *e | Vent Valve: Off (Vent) | *f | to Canister Filter (Atmosphere) |
| *g | Leak Detection Pump: Off | *h | Vent Valve: on (closed) |
| *i | Leak Detection Pump: on | - | - |



| 1.CONFIRM DTC |
Turn the ignition switch off and wait for 10 seconds.
Turn the ignition switch to ON.
Turn the ignition switch off and wait for 10 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm DTCs and freeze frame data.
If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.

| NEXT | |
| 2.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE) |
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | |
| 3.PERFORM EVAPORATIVE SYSTEM CHECK (MANUAL MODE) |

Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Manual Mode.
| NEXT | |
| 4.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6) |

Check the EVAP pressure in step 1/6.
| DTC*1 | Test Result | Suspected Trouble Area | Proceed to |
| - | Virtually no variation in EVAP pressure | Not yet determined | A |
| P0451 | EVAP pressure fluctuates by 0.3 kPa-g (2.25 mmHg-g) or more | Canister pressure sensor noise | B |
| (P0452 or P0453)*2 |
| Canister pressure sensor or its circuit has malfunction | C |
|
| ||||
|
| ||||
| A | |
| 5.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 1/6 TO 2/6) |

Check the EVAP pressure in steps 1/6 and 2/6.
| DTC* | Test Result | Suspected Trouble Area | Proceed to |
| - | Virtually no variation in EVAP pressure during step 1/6. Then decreases to reference pressure. | Not yet determined | A |
| P2402 | Small difference between EVAP pressures during steps 1/6 and 2/6 | Leak detection pump stuck ON | B |
|
| ||||
| A | |
| 6.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6) |

| DTC* | Test Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure in step (b) between -4.85 kPa-g and -1.057 kPa-g (-36.4 mmHg-g and -7.93 mmHg-g) | Not yet determined | A |
| P043F and P2401 | EVAP pressure in step (b) -1.057 kPa-g (-7.93 mmHg-g) or higher |
| B |
| P043E | EVAP pressure in step (b) below -4.85 kPa-g (-36.4 mmHg-g) | Reference orifice clogged | C |
| P2419 | EVAP pressure in step (a) higher than -1 kPa-g (-7.5 mmHg-g) |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 7.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 2/6 TO 3/6) |

Check the EVAP pressure increase in step 3/6.
| DTC* | Test Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 2/6 to step 3/6 | Not yet determined | A |
| P2420 | No variation in EVAP pressure despite proceeding from step 2/6 to step 3/6 |
| B |
| P0451 | No variation in EVAP pressure during steps 1/6 through 3/6 |
| C |
|
| ||||
|
| ||||
| A | |
| 8.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6) |

Wait until the EVAP pressure change over 30 seconds is less than 0.1 kPa-g (0.75 mmHg-g).
Measure the EVAP pressure and record it.
| NEXT | |
| 9.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 4/6) |

Check the EVAP pressure in step 4/6.
| DTC*1 | Test Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6 | Not yet determined | A |
| P0441*2 | EVAP pressure increases by 0.3 kPa-g (2.25 mmHg-g) or more within 10 seconds of proceeding from step 3/6 to step 4/6 |
| B |
| P0441 | Variation in EVAP pressure less than 0.3 kPa-g (2.25 mmHg-g) for 10 seconds after proceeding from step 3/6 to step 4/6 |
| C |
|
| ||||
|
| ||||
| A | |
| 10.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 5/6) |

Check the EVAP pressure in step 5/6.
Compare the EVAP pressure from step 3/6 and the second reference pressure (step 5/6).
| DTC* | Test Result | Suspected Trouble Area | Proceed to |
| - | EVAP pressure (step 3/6) lower than second reference pressure (step 5/6) | Not yet determined (no leakage from EVAP system) | A |
| P0441 and P0455 | EVAP pressure (step 3/6) higher than [second reference pressure (step 5/6) x 0.2] |
| B |
| P0456 | EVAP pressure (step 3/6) higher than second reference pressure (step 5/6) | EVAP small leak | B |
|
| ||||
|
| ||||
| 11.PERFORM EVAPORATIVE SYSTEM CHECK (STEP 3/6) |

Check the EVAP pressure in step 3/6.
| DTC* | Test Result | Suspected Trouble Area | Proceed to |
| P043F | EVAP pressure less than [reference pressure] measured in step 2/6 | Reference orifice high-flow | A |
| P2401 | EVAP pressure almost same as [reference pressure] measured in step 2/6 | Leak detection pump stuck OFF | B |
|
| ||||
|
| ||||
| 12.INSPECT CANISTER PUMP MODULE (CANISTER PRESSURE SENSOR CIRCUIT) |
Check the canister pressure sensor circuit, referring to DTC P0451 canister pressure sensor circuit inspection procedure (Click here).
|
| ||||
| 13.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION) |
![]() |
Turn the ignition switch off.
Disconnect the R12 canister pump module connector.
Apply battery voltage to the VLVB and VGND terminals of the canister pump module.
Touch the canister pump module to confirm the vent valve operation.
| Condition | Tester Result | Suspected Trouble Area | Proceed to |
| Apply battery voltage to terminals VLVB and VGND | Operating |
| A |
| Not operating | Vent valve | B |
| *a | Component without harness connected (Canister Pump Module) |
|
| ||||
| A | |
| 14.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE) |
Disconnect the ECM connector.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-30 (VPMP) - R12-1 (VGND) | Always | Below 1 Ω |
| A24-30 (VPMP) or R12-1 (VGND) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK |
| A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
| A | |
| 15.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND) |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| R12-4 (MGND) - Body ground | Always | Below 1 Ω |
| A |
| 10 kΩ or higher | Wire harness or connector between canister pump module and body ground | B |
|
| ||||
| A | |
| 16.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE) |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-49 (MPMP) - R12-3 (MTRB) | Always | Below 1 Ω |
| A24-49 (MPMP) or R12-3 (MTRB) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK |
| A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
|
| ||||
| 17.PERFORM ACTIVE TEST USING TECHSTREAM (PURGE VSV) |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.
![]() |
Disconnect the hose (connected to the canister) from the purge VSV.
Start the engine.
Using the Techstream, turn off the purge VSV (Activate the VSV for EVAP Control: OFF).
Use your finger to confirm that the purge VSV has no suction.
Using the Techstream, turn on the purge VSV (Activate the VSV for EVAP Control: ON).
Use your finger to confirm that the purge VSV has suction.
| Test Result | Suspected Trouble Area | Proceed to |
| No suction when purge VSV turned OFF, and suction applied when turned ON | Blockage in the purge line is considered (based on result of step 9):
| A |
Leakage is considered (based on result of step 10):
| B | |
| Suction applied when purge VSV turned OFF | Purge VSV stuck open | C |
| No suction when purge VSV turned ON |
| D |
| *1 | Purge VSV |
| *2 | Hose (to Canister) |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 18.INSPECT EVAP HOSE (PURGE VSV - CANISTER) |
Check for blockages in the EVAP purge line between the purge VSV and canister.
|
| ||||
| OK | |
| 19.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER) |
Check for filter blockage in the canister assembly (Click here).
|
| ||||
|
| ||||
| 20.CHECK FUEL TANK CAP ASSEMBLY |
Check that the fuel tank cap is correctly installed and confirm that the fuel tank cap meets OEM specifications.
Tighten the fuel tank cap firmly (only one click sound is heard).
| Test Result | Suspected Trouble Area | Proceed to |
| Fuel tank cap correctly installed | - | A |
| Fuel tank cap loose |
| B |
| Defective fuel tank cap | - | B |
| No fuel tank cap | - | C |
|
| ||||
|
| ||||
|
| ||||
| 21.INSPECT PURGE VSV |
Turn the ignition switch off.
Disconnect the purge VSV connector.
![]() |
Disconnect the hose (connected to the canister) from the purge VSV.
Start the engine.
Use your finger to confirm that the purge VSV has no suction.
| Test Result | Suspected Trouble Area | Proceed to |
| No suction |
| A |
| Suction applied | Purge VSV | B |
| *1 | Purge VSV |
| *2 | Hose (to Canister) |
| *3 | Connector |
|
| ||||
|
| ||||
| 22.INSPECT EVAP HOSE (PURGE VSV - CANISTER) |
Check for blockages in the EVAP purge line between the purge VSV and canister.
|
| ||||
| OK | |
| 23.CHECK EVAP HOSE (PURGE VSV - INTAKE MANIFOLD) |
![]() |
Disconnect the hose (connected to the intake manifold) from the purge VSV.
Start the engine.
Use your finger to confirm that the hose has suction.
| Test Result | Suspected Trouble Area | Proceed to |
| Suction applied | EVAP hose between purge VSV and intake manifold normal
| A |
| No suction |
| B |
| *1 | Purge VSV |
| *2 | Hose (to Intake Manifold) |
|
| ||||
| A | |
| 24.INSPECT PURGE VSV |
![]() |
Remove the purge VSV.
Apply battery voltage to the terminals of the purge VSV.
Using an air gun, confirm that air flows from port A to port B.
| Test Result | Condition | Suspected Trouble Area | Proceed to |
| Air flows | Battery voltage is applied to purge VSV terminals | Purge VSV normal
| A |
| No air flow | Battery voltage is applied to purge VSV terminals | Purge VSV | B |
| *1 | Purge VSV |
| *2 | Port A |
| *3 | Port B |
|
| ||||
| A | |
| 25.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PURGE VSV) |
![]() |
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| D29-1 - Body ground | Ignition switch ON | 11 to 14 V | Purge VSV power source normal
| A |
| Ignition switch ON | Other than result above | Wire harness or connectors between purge VSV and battery | B |
| *a | Front view of wire harness connector (to Purge VSV) |
|
| ||||
| A | |
| 26.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Disconnect the ECM connector.
Disconnect the purge VSV connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-63 (PRG) - D29-2 | Always | Below 1 Ω |
| D74-63 (PRG) or D29-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
|
| ||||
| 27.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE) |

Turn the ignition switch off.
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| R12-5 (VLVB) - Body ground | Ignition switch ON | 11 to 14 V |
| A |
| Ignition switch ON | Below 3 V | Power source wire harness of vent valve | B |
| *a | Front view of wire harness connector (to Canister Pump Module) |
|
| ||||
| A | |
| 28.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION) |
![]() |
Turn the ignition switch off.
Disconnect the R12 canister pump module connector.
Apply battery voltage to the VLVB and VGND terminals of the canister pump module.
Touch the canister pump module to confirm the vent valve operation.
| Condition | Tester Result | Suspected Trouble Area | Proceed to |
| Apply battery voltage to terminals VLVB and VGND | Operating |
| A |
| Not operating | Vent valve | B |
| *a | Component without harness connected (Canister Pump Module) |
|
| ||||
| A | |
| 29.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the ECM connector.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-30 (VPMP) - R12-1 (VGND) | Always | Below 1 Ω |
| A24-30 (VPMP) or R12-1 (VGND) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK |
| A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
| A | |
| 30.INSPECT CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER) |
Check for filter blockage in the canister assembly (Click here).
|
| ||||
|
| ||||
| 31.CHECK TERMINAL VOLTAGE (CANISTER PUMP MODULE) |

Turn the ignition switch off.
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Test Result | Suspected Trouble Area | Proceed to |
| R12-3 (MTRB) - Body ground | Ignition switch ON | 9 to 14 V |
| A |
| Below 3 V |
| B |
| *a | Front view of wire harness connector (to Canister Pump Module) |
|
| ||||
| A | |
| 32.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND) |
Turn the ignition switch off.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| R12-4 (MGND) - Body ground | Always | Below 1 Ω | Leak detection pump | A |
| Always | 10 kΩ or higher | Wire harness or connector between canister pump module and body ground | B |
|
| ||||
|
| ||||
| 33.CHECK HARNESS AND CONNECTOR (ECM - CANISTER PUMP MODULE) |
Turn the ignition switch off.
Disconnect the ECM connector.
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-49 (MPMP) - R12-3 (MTRB) | Always | Below 1 Ω |
| A24-49 (MPMP) or R12-3 (MTRB) - Body ground | Always | 10 kΩ or higher |
| Result | Suspected Trouble Area | Proceed to |
| OK | ECM | A |
| NG | Wire harness or connector between ECM and canister pump module | B |
|
| ||||
|
| ||||
| 34.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT) |
Stop the engine.
Disconnect the EVAP hose from the intake manifold.
Start the engine.
Use your finger to confirm that the port of the intake manifold has suction.
| Test Result | Suspected Trouble Area | Proceed to |
| Suction applied | EVAP hose between intake manifold and purge VSV | A |
| No suction | Intake manifold | B |
|
| ||||
|
| ||||
| 35.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY |
|
| ||||
| 36.REPLACE FUEL TANK CAP ASSEMBLY |
|
| ||||
| 37.LOCATE EVAP PART WHICH IS LEAKING |

| *1 | EVAP Tester | *2 | Adapter |
| *3 | Canister Outlet Hose | - | - |
Disconnect the canister outlet hose.
Connect an EVAP tester to the canister pump module with an adapter.
Pressurize the EVAP system to between 3.2 and 3.7 kPa (24 and 28 mmHg).
Apply soapy water to the piping and connecting parts of the EVAP system.
Look for areas where bubbles appear. Bubbles indicate the leak point.
Repair or replace the leak point.
|
| ||||
| 38.REPAIR CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank | *2 | Fuel Tank Vent Hose |
| *3 | Canister Assembly | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) | *6 | Canister Outlet Hose |
| *a | Inspection Area (check for disconnection and/or cracks) | - | - |
|
| ||||
| 39.REPLACE PURGE VSV |
Replace the purge VSV (Click here).
|
| ||||
| 40.REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| ||||
| 41.REPAIR OR REPLACE EVAP PURGE LINE (INTAKE MANIFOLD - PURGE VSV) |
|
| ||||
| 42.INSPECT INTAKE MANIFOLD (EVAP PURGE PORT) |
Check that the EVAP purge port of the intake manifold is not clogged. If necessary, replace the intake manifold.
|
| ||||
| 43.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS |
Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.
|
| ||||
| 44.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VSV - CANISTER) |
|
| ||||
| 45.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel Tank | *2 | Fuel Tank Vent Hose |
| *3 | Canister Assembly | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) | *6 | Canister Outlet Hose |
| *a | Inspection Area (check for disconnection and/or cracks) | - | - |
| NEXT | |
| 46.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE) |
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Result | Proceed to |
| EVAP system DTCs are output | A |
| DTC is not output (Pending DTC is not output) | B |
|
| ||||
| A | |
| 47.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 48.REPLACE CANISTER ASSEMBLY |
Replace the canister assembly (Click here).

| *1 | Fuel Tank | *2 | Fuel Tank Vent Hose |
| *3 | Canister Assembly | *4 | Canister Pump Module - Canister Pressure Sensor - Leak Detection Pump - Vent Valve |
| *5 | Fuel Tank Inlet Pipe Sub-Assembly (Canister Filter) | *6 | Canister Outlet Hose |
| *a | Inspection Area (check for disconnection and/or cracks) | - | - |
| NEXT | |
| 49.PERFORM EVAPORATIVE SYSTEM CHECK (AUTOMATIC MODE) |
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | ||
| ||
| Key-off monitor confirmation |
Preconditions
The monitor will not run unless:
Monitor Conditions
Monitor Status
| Purge flow monitor confirmation (P0441) |
Preconditions
The monitor will not run unless:
Monitor Conditions
Monitor Status