DTC P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2) |
DTC P1342 Camshaft Position Sensor "A" Low Input (MRE) |
DTC P1343 Camshaft Position Sensor "A" High Input (MRE) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P1340 | No camshaft position sensor signal to ECM during cranking (2 trip detection logic) |
|
| No camshaft position sensor signal to ECM with engine speed 600 rpm or more | ||
| P1342 | Output voltage of camshaft position sensor less than 0.3 V for 4 seconds (1 trip detection logic) | |
| P1343 | Output voltage of camshaft position sensor more than 4.7 V for 4 seconds (1 trip detection logic) |
| Related DTCs | P1340: Camshaft position sensor verify pulse input P1340: Camshaft position / Crankshaft position misalignment P1342: Camshaft position sensor range check (low voltage) P1343: Camshaft position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, Engine speed sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: P1340 camshaft position sensor verify pulse input P1342: Camshaft position sensor range check (low voltage) P1343: Camshaft position sensor range check (high voltage) 5 seconds: P1340 camshaft position / crankshaft position misalignment |
| MIL Operation | 2 driving cycles: P1340 camshaft position sensor verify pulse input Immediate: P1340 camshaft position / crankshaft position misalignment and P1342, P1343 camshaft position sensor range check |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Starter | ON (Not starter ON again) |
| Minimal battery voltage while starter ON | Less than 11 V |
| Monitor runs whenever following DTCs not present | P0342, P0343 (VVT sensor) P1342, P1343 (Camshaft position sensor) |
| Engine RPM | 600 rpm or more |
| Starter | OFF |
| Camshaft position sensor range check fail (P1342, P1343) | Not detected |
| Camshaft position sensor range | 0.3 to 4.7 V |
| Monitor runs whenever following DTCs not present | P0340, P1340 (Camshaft position sensor) |
| Time after ignition switch off to ON | 2 seconds or more |
| Camshaft position sensor verify pulse input fail (P1340) | Not detected |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Camshaft position signal | No signal |
| Camshaft position and crankshaft position phase | Misaligned |
| Camshaft position sensor voltage | Less than 0.3 V |
| Camshaft position sensor voltage | Higher than 4.7 V |
| Camshaft position sensor signal |
|

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the D6 camshaft position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D6-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR) |
Disconnect the D6 camshaft position sensor connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D6-1 (G2) - D74-90 (G2) | Always | Below 1 Ω |
| D6-2 (G-) - D74-89 (G2-) | Always | Below 1 Ω |
| D6-1 (G2) or D74-90 (G2) - Body ground | Always | 10 kΩ or higher |
| D6-2 (G-) or D74-89 (G2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT SENSOR INSTALLATION |
![]() |
Check the camshaft position sensor installation.
|
| ||||
| OK | |
| 4.INSPECT CAMSHAFT TIMING PLATE (SIGNAL PLATE TOOTH) |
Check the teeth of the signal plate.
|
| ||||
| OK | |
| 5.REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
| NEXT | |
| 6.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P1340, P1342 and/or P1343 are output | B |
|
| ||||
| A | ||
| ||