Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The intake camshaft has 3 teeth on its outer circumference. When the camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC Code
DTC Detection Condition
Trouble Area
P0340
P0345
No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0342
P0347
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0343
P0348
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor for intake camshaft circuit
  2. VVT sensor for intake camshaft
  3. Intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM

  1. A217926E02
    Reference: Inspection using an oscilloscope

    Standard:

    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    D74-110 (NE+) - D74-111 (NE-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    D74-92 (VV1+) - D74-91 (VV1-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    D74-87 (VV2+) - D74-88 (VV2-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown

    HINT:
    VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the intake camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (for Bank 1) verify pulse input
P0340: VVT sensor (for Bank 1) range check (chattering)
P0342: VVT position sensor (for Bank 1) range check (low voltage)
P0343: VVT position sensor (for Bank 1) range check (high voltage)
P0345: VVT sensor (for Bank 2) verify pulse input
P0345: VVT sensor (for Bank 2) range check (chattering)
P0347: VVT position sensor (for Bank 2) range check (low voltage)
P0348: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds: P0340, P0345
4 seconds: Others
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not stored
None

P0340, P0345 (Verify Pulse Input) 
Engine speed
600 rpm or more
Battery voltage
8 V or more
Starter
OFF
Ignition switch
ON
VVT sensor voltage
0.3 to 4.7 V
VVT sensor range check low voltage fail (P0342, P0347)
Not detected
VVT sensor range check high voltage fail (P0343, P0348)
Not detected

P0342, P0343, P0347, P0348 (Low Voltage, High Voltage) 
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345)
Not detected
Battery Voltage
8 V or more

TYPICAL MALFUNCTION THRESHOLDS


P0340, P0345 (Verify pulse input): 
VVT sensor signal
No signal

P0342, P0347 (Low voltage): 
VVT sensor voltage
Less than 0.3 V

P0343, P0348 (High voltage): 
VVT sensor voltage
More than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN


A198821E06

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [B].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A165014E03


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
A107149E65
  1. Disconnect the D37 or D39 VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)
  1. Disconnect the D37 or D39 VVT sensor connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D37-1 (VVL+) - D74-92 (VV1+)
    Always
    Below 1 Ω
    D37-2 (VVL-) - D74-91 (VV1-)
    Always
    Below 1 Ω
    D39-1 (VVR+) - D74-87 (VV2+)
    Always
    Below 1 Ω
    D39-2 (VVR-) - D74-88 (VV2-)
    Always
    Below 1 Ω
    D37-1 (VVL+) or D74-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    D37-2 (VVL-) or D74-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    D39-1 (VVR+) or D74-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    D39-2 (VVR-) or D74-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)


    BR03795E17
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.CHECK INTAKE CAMSHAFT (TEETH)
  1. Check the teeth of the camshaft.

    OK:
    Teeth do not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft assembly (Click here).



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5.REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Refer to the confirmation driving pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END