DTC P0340 Camshaft Position Sensor Circuit |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 P0345 | No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic) |
|
| P0342 P0347 | Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic) |
|
| P0343 P0348 | Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-92 (VV1+) - D74-91 (VV1-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-87 (VV2+) - D74-88 (VV2-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0340: VVT position sensor (for Bank 1) verify pulse input P0342: VVT position sensor (for Bank 1) range check (low voltage) P0343: VVT position sensor (for Bank 1) range check (high voltage) P0345: VVT position sensor verify pulse input (for Bank 2) P0347: VVT position sensor (for Bank 2) range check (low voltage) P0348: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | P0340, P0345: 5 seconds P0342, P0343, P0347, P0348: 4 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0342, P0343, P0347, P0348 (VVT sensor) |
| Engine speed | 600 rpm or more |
| Starter | OFF |
| Camshaft position sensor voltage | 0.3 to 4.7 V |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Monitor runs whenever following DTCs are not present | P0340, P0345 (VVT sensor) |
| Starter | OFF |
| Ignition switch ON and time after ignition switch is off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the VVT sensor (for intake side) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM) |
![]() |
Disconnect the VVT sensor (for intake side) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-1 (VVL+) - D74-92 (VV1+) | Always | Below 1 Ω |
| D37-2 (VVL-) - D74-91 (VV1-) | Always | Below 1 Ω |
| D39-1 (VVR+) - D74-87 (VV2+) | Always | Below 1 Ω |
| D39-2 (VVR-) - D74-88 (VV2-) | Always | Below 1 Ω |
| D37-1 (VVL+) or D74-92 (VV1+) - Body ground | Always | 10 kΩ or higher |
| D37-2 (VVL-) or D74-91 (VV1-) - Body ground | Always | 10 kΩ or higher |
| D39-1 (VVR+) or D74-87 (VV2+) - Body ground | Always | 10 kΩ or higher |
| D39-2 (VVR-) or D74-88 (VV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE SIDE) |
![]() |
Check the VVT sensor (for intake side) installation.
|
| ||||
| OK | |
| 4.INSPECT INTAKE CAMSHAFT (TEETH) |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN) |

Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.
Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.REPLACE VVT SENSOR (FOR INTAKE SIDE) |
Replace the VVT (for intake side) sensor (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs.
Refer to the confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 is output | B |
|
| ||||
| A | ||
| ||