Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Cranking Holding Function Circuit

for Preparation Click here


DESCRIPTION

The cranking holding control system provides current to the starter when the ECM detects the ignition switch start signal (STSW). When the ECM determines that the engine has started, the system cuts current to the starter. When the ECM receives the STSW signal, it turns on the ACC Cut relay, which prevents flickering of the combination meter, clock, audio system, etc. Also, the ECM sends a signal to terminal STAR of the ECM. Then the STAR output signal travels through the park/neutral position (PNP) switch to the ST relay, causing the starter to activate.
When the engine is cranking, the starter operation signal is sent to terminal STA of the ECM.

A103821E73


WIRING DIAGRAM


A247753E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CRANKING
  1. Check the cranking of the engine.

    Result 
    Test Result
    Proceed to
    Cranking possible and holding control operates
    A
    Does not crank
    B
    Cranking possible but holding control does not operate
    C



B
Go to step 2

C
Go to step 11
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and when the engine is started.

    Standard:
    Ignition Switch Position
    Display (Starter Signal)
    ON
    OFF
    START
    ON



NG
Go to step 7
OK


3.INSPECT STARTER RELAY (ST)
  1. Inspect the starter relay (ST) (Click here).



NG
REPLACE STARTER RELAY (ST)
OK


4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - STARTER RELAY (ST))
  1. Disconnect the park/neutral Position switch assembly connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay (1) - D35-5
    Always
    Below 1 Ω
    ST relay (1) or D35-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A247750E01
  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay (2) - ST relay (5)
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Starter Relay (ST)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BATTERY, BODY GROUND)
OK


6.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (for 1.6 kW type) (Click here).

  1. Inspect the starter assembly (for 1.4 kW type) (Click here).

    Result 
    Test Result
    Proceed to
    OK
    A
    NG (for 1.6 kW type)
    B
    NG (for 1.4 kW type)
    C



B
REPLACE STARTER ASSEMBLY (Click here)

C
REPLACE STARTER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER ASSEMBLY - STARTER RELAY (ST), BATTERY) 

7.CHECK IGNITION SWITCH ASSEMBLY (POWER SOURCE)
A163734E03
  1. Disconnect the ignition switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J9-5 (AM2) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY POSITIVE TERMINAL)
OK


8.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
C159064E23
  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D35-4 - Body ground
    Engine cranking
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
OK


10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) 

11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the ignition switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    J9-7 (ST2) - A24-14 (STSW)
    Always
    Below 1 Ω
    J9-7 (ST2) or A24-14 (STSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D35-4 - D74-16 (STAR)
    Always
    Below 1 Ω
    D35-4 or D74-16 (STAR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)