Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E13
Text in Illustration 
*1
VVT Sensor
*2
Crankshaft Position Sensor
*3
ECM
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emissions levels. High concentrations of HC can also cause increases in the Three-way Catalytic Converter (TWC) temperature, which may cause damage to the Three-way Catalytic Converter (TWC). To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the Three-way Catalytic Converter (TWC) reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. A misfire is counted when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks when detect immediately).
  2. Emission deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Intake system
  14. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in the Three-way Catalytic Converter (TWC) (MIL blinks when detect immediately).
  2. Emission deterioration misfire occurs (MIL illuminates).
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL (immediate detection logic) and sets a DTC (2 trip detection logic) when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive number of misfires (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL immediately when either one of the following conditions, which could cause damage to the Three-way Catalytic Converter (TWC), is detected. Also, the ECM stores a DTC when either one of the following conditions is detected (2 trip detection logic).
  1. At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
  2. At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and VVT sensor
Required Sensors/Components (Related)
Engine coolant temperature, intake air temperature sensors and mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: MIL illuminates when misfire detected
MIL flashes immediately: When catalyst-damaging misfire occurs
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or higher
VVT system
Not operated by scan tool
Engine speed
400 to 5900 rpm
Either of following conditions (a) or (b) met
-
(a) Engine coolant temperature at engine start
Higher than -7°C (19°F)
(b) Engine coolant temperature
Higher than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emissions-related Misfire 
First 1000 revolutions after engine start, or Check Mode
1000 crankshaft revolutions
Except above
1000 crankshaft revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks) 
All of following conditions 1, 2, 3 and 4 met
200 crankshaft revolutions x 3
Except above (MIL blinks immediately)
Crankshaft 200 revolutions
1. Driving cycle
1st
2. Check mode
OFF
3. Engine speed
Less than 1900 rpm
4. Intake air amount per revolution
Less than 1.4 g/rev

TYPICAL MALFUNCTION THRESHOLDS


Malfunction Threshold for Emissions-related Misfire 
Misfire rate
1.5% or more

Malfunction Threshold for Catalyst-damaging Misfire (MIL Blinks) 
Number of misfires per 200 revolutions
77 or more (varies with intake air amount and engine speed)
Paired cylinders misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM

Refer to DTC P0102 .
Refer to DTC P0351 .
Refer to Fuel Injector Circuit .

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTCs and freeze frame data.
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (cylinder No. 1 to No. 6) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine speed and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

    Engine Speed
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.

  10. Record the DTCs, freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 30 seconds.
  12. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors may be a cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is being used.
    3. The spark plugs are dirty.
  5. After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5 and No. 6).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speeds. If misfires only occur during high engine speed driving, only DTC P0300 is stored.
    In the event of DTC P0300 being output, perform the following operations:
    1. Clear the DTCs (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfire counts of each cylinder or the DTCs using the Techstream.
    4. Repair the cylinders that have a high misfire count or are indicated by DTCs.
    5. After finishing repairs, conduct the confirmation driving pattern again in order to verify that DTC P0300 is not stored.
  8. When Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-15%, the air-fuel ratio may be rich (-15% or less) or lean (+15% or more).
  9. When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires may have occurred while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections .

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result 
    Data List
    Techstream Display
    Proceed to
    Catalyst OT MF F/C
    AVAIL (Avail)
    A
    NOT AVL (Not Avl)
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved at 3000 rpm or less.


NEXT


6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6.

  1. Allow the engine to idle.

  1. Read the values for Cylinder #1 Misfire Count to Cylinder #6 Misfire Count displayed on the Techstream. If no misfires are counted in any cylinders, perform the following procedure:

    1. Move the shift lever to D.

    2. Check Cylinder #1 Misfire Count to Cylinder #6 Misfire Count.

    3. If misfires are still not being counted, perform procedures "A" and "B", and then check the misfire counts again.
      Procedure A: Drive the vehicle while matching the vehicle conditions to the Misfire RPM and Misfire Load values noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedure above.
      Procedure B: Read Cylinder #1 Misfire Count to Cylinder #6 Misfire Count or the DTCs output on the Techstream.
      Result 
      Result
      Proceed to
      Most misfires occur in only 1 or 2 cylinders
      A
      3 cylinders or more have equal misfire counts
      B

      HINT:
      1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
      2. If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), misfire may be detected only when the engine is cold.
      3. If the freeze frame data's record of the Engine Run Time is less than 120 seconds, misfire may only be detected immediately after the engine is started.



B
Go to step 18
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).
    3. Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here).


NEXT


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A208644E20
  1. Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Turn the ignition switch off.



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK HARNESS AND CONNECTOR
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


15.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


16.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: off).



NG
Go to step 29
OK


17.CHECK VALVE TIMING


    A103826E11
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark

  1. Reinstall the cylinder head cover RH and LH.



OK
Go to step 29

NG
ADJUST VALVE TIMING (Click here)

18.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


19.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


20.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


21.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: off).



NG
Go to step 29
OK


22.CHECK VALVE TIMING


    A103826E11
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING (Click here)
OK


23.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


24.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count (to Cylinder #6 Misfire Count).
    3. Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here).


NEXT


25.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


26.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A208644E20
  1. Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Turn the ignition switch off.



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


27.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
  1. Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


29.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


30.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output)
    A
    NORMAL
    (No DTC is output)
    B



B
END
A


31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D7-5 (VG) - D74-74 (VG)
    Always
    Below 1 Ω
    D7-4 (E2G) - D74-75 (E2G)
    Always
    Below 1 Ω
    D7-5 (VG) or D74-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


32.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    1. If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).


NEXT


33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (No DTC is output)
    A
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output)
    B



B
REPLACE ECM (Click here)
A

END 

34.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)