Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

  1. If the driver side manual UP/DOWN function does not operate, there may be a malfunction in master switch, driver side motor or harness and connector.

WIRING DIAGRAM


B149728E04


INSPECTION PROCEDURE

1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B231474E03
  1. Remove the motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)

B149729E06

  1. Disconnect the N2 master switch connector.

  1. Disconnect the N3 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Regular Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-10 (U) - N3-2
    Always
    Below 1 Ω
    N2-12 (D) - N3-1
    Always
    Below 1 Ω
    N2-10 (U) or N3-2 - Body ground
    Always
    10 kΩ or higher
    N2-12 (D) or N3-1 - Body ground
    Always
    10 kΩ or higher
    for Double Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-3 (U) - N3-2
    Always
    Below 1 Ω
    N2-4 (D) - N3-1
    Always
    Below 1 Ω
    N2-3 (U) or N3-2 - Body ground
    Always
    10 kΩ or higher
    N2-4 (D) or N3-1 - Body ground
    Always
    10 kΩ or higher
    for CrewMax: 
    Tester Connection
    Condition
    Specified Condition
    N2-3 (U) - N3-2
    Always
    Below 1 Ω
    N2-4 (D) - N3-1
    Always
    Below 1 Ω
    N2-3 (U) or N3-2 - Body ground
    Always
    10 kΩ or higher
    N2-4 (D) or N3-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B166134E10

  1. Remove the master switch (Click here).

  1. Reconnect the master switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Regular Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-10 (U) - N2-7 (E)
    Ignition switch ON, driver side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-12 (D) - N2-7 (E)
    Ignition switch ON, driver side switch of master switch OFF → DOWN
    Below 1 V → 11 to 14 V
    N2-12 (D) - N2-7 (E)
    Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
    Below 1 V → 11 to 14 V → Below 1 V
    for Double Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-3 (U) - N2-1 (E)
    Ignition switch ON, driver side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-4 (D) - N2-1 (E)
    Ignition switch ON, driver side switch of master switch OFF → DOWN
    Below 1 V → 11 to 14 V
    N2-4 (D) - N2-1 (E)
    Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
    Below 1 V → 11 to 14 V → Below 1 V
    for CrewMax: 
    Tester Connection
    Condition
    Specified Condition
    N2-3 (U) - N2-1 (E)
    Ignition switch ON, driver side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-4 (D) - N2-1 (E)
    Ignition switch ON, driver side switch of master switch OFF → DOWN
    Below 1 V → 11 to 14 V
    N2-4 (D) - N2-1 (E)
    Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open
    Below 1 V → 11 to 14 V → Below 1 V



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL (Click here)