Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/o Jam Protection Function) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

  1. If the front passenger side manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator switch assembly, front passenger side motor, master switch or harness and connector.

WIRING DIAGRAM


B173121E06


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BATTERY)
B149730E20
  1. Disconnect the M2 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M2-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
B166135E04
  1. Remove the power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)

B173122E04

  1. Disconnect the M2 switch connector.

  1. Disconnect the M3 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-1 (D) - M3-1
    Always
    Below 1 Ω
    M2-4 (U) - M3-2
    Always
    Below 1 Ω
    M2-1 (D) or M3-1 - Body ground
    Always
    10 kΩ or higher
    M2-4 (U) or M3-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
B231476E02
  1. Remove the front passenger side motor (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - POWER WINDOW REGULATOR SWITCH)

B173123E04

  1. Disconnect the N2 master switch connector.

  1. Disconnect the M2 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Regular Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-16 (U) - M2-5 (SU)
    Always
    Below 1 Ω
    N2-18 (D) - M2-2 (SD)
    Always
    Below 1 Ω
    N2-16 (U) or M2-5 (SU) - Body ground
    Always
    10 kΩ or higher
    N2-18 (D) or M2-2 (SD) - Body ground
    Always
    10 kΩ or higher
    for Double Cab: 
    Tester Connection
    Condition
    Specified Condition
    N2-16 (U) - M2-5 (SU)
    Always
    Below 1 Ω
    N2-15 (D) - M2-2 (SD)
    Always
    Below 1 Ω
    N2-16 (U) or M2-5 (SU) - Body ground
    Always
    10 kΩ or higher
    N2-15 (D) or M2-2 (SD) - Body ground
    Always
    10 kΩ or higher
    for CrewMax: 
    Tester Connection
    Condition
    Specified Condition
    N2-16 (U) - M2-5 (SU)
    Always
    Below 1 Ω
    N2-15 (D) - M2-2 (SD)
    Always
    Below 1 Ω
    N2-16 (U) or M2-5 (SU) - Body ground
    Always
    10 kΩ or higher
    N2-15 (D) or M2-2 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B166134E11

  1. Remove the master switch (Click here).

  1. Reconnect the master switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Regular Cab: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-16 (U) - N2-7 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-18 (D) - N2-7 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → DOWN
    for Double Cab: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-16 (U) - N2-1 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-15 (D) - N2-1 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → DOWN
    for CrewMax: 
    Tester Connection
    Switch Condition
    Specified Condition
    N2-16 (U) - N2-1 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → UP
    Below 1 V → 11 to 14 V
    N2-15 (D) - N2-1 (E)
    Ignition switch ON, front passenger side switch of master switch OFF → DOWN



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL (Click here)