Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

  1. If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear switch RH, the rear motor RH, the master switch, or the harness or connector.

WIRING DIAGRAM


B231419E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - BATTERY)


    B149730E19
  1. Disconnect the O5 switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O5-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    B166135E03
  1. Remove the rear switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 2 (SD)
    OFF
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    DOWN
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)


    B191455E05
  1. Disconnect the O5 switch connector.

  1. Disconnect the O3 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O5-1 (D) - O3-1
    Always
    Below 1 Ω
    O5-4 (U) - O3-2
    Always
    Below 1 Ω
    O5-1 (D) - Body ground
    Always
    10 kΩ or higher
    O5-4 (U) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    B231476E01
  1. Remove the rear motor RH (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH)


    B191456E05
  1. Disconnect the N2 master switch connector.

  1. Disconnect the O5 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-10 (U) - O5-5 (SU)
    Always
    Below 1 Ω
    N2-16 (D) - O5-2 (SD)
    Always
    Below 1 Ω
    N2-10 (U) - Body ground
    Always
    10 kΩ or higher
    N2-16 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)