Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY


    C159283E01
  1. Install the differential support with the F and G bolts.

    Torque:
    100 N*m{ 1019 kgf*cm , 74 ft.*lbf }

  1. Using a jack, slowly raise the front differential carrier assembly to its installation position.

  1. Temporarily install the A, B, C, D and E bolts.

  1. Tighten the A bolt.

    Torque:
    113 N*m{ 1152 kgf*cm , 83 ft.*lbf }

  1. Tighten the B and C bolts.

    Torque:
    113 N*m{ 1152 kgf*cm , 83 ft.*lbf }

  1. Tighten the D and E bolts.

    Torque:
    113 N*m{ 1152 kgf*cm , 83 ft.*lbf }

  1. Connect the differential actuator hose.

  1. Connect the differential actuator connector.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)


3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure as the LH side.



4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


5. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    1GR-FE and 1UR-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }



6. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



7. INSTALL FRONT WHEEL
  1. Install the front wheels.

    Torque:
    for aluminum wheel:
    131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
    for steel wheel:
    209 N*m{ 2131 kgf*cm , 154 ft.*lbf }