Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15D3    Stereo Component Amplifier Disconnected

for Preparation Click here


DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.
When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B15D3
When either condition below is met:
  1. Stereo component amplifier assembly is/was not connected while the ignition switch is ACC or ON.
  2. Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.
  1. Stereo component amplifier assembly
  2. Navigation receiver assembly
  3. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM


E280957E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.
    Result 
    Result
    Proceed to
    DTC B15C3 is not output.
    A
    DTC B15C3 is output.
    B



B
GO TO DTC "B15C3" IN DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check that optional components (including associated wiring) which generate radio waves are not installed.
    Result 
    Result
    Proceed to
    Optional components (including associated wiring) are installed.
    A
    Optional components (including associated wiring) are not installed.
    B

    HINT:
    1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
    2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE) 

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)


    E280958E02
  1. Disconnect the stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J143-6 (GND) - Body ground
    Always
    Below 1 Ω
    J143-7 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J142-1 (+B) - J143-6 (GND)
    Always
    11 to 14 V
    J142-5 (+B2) - J143-6 (GND)
    Always
    11 to 14 V
    J141-12 (ACC) - J143-6 (GND)
    Ignition switch ACC
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. Disconnect the J135 navigation receiver assembly connector.

  1. Disconnect the J141 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J135-7 (TX1+) - J141-8 (TX+)
    Always
    Below 1 Ω
    J135-8 (TX1-) - J141-7 (TX-)
    Always
    Below 1 Ω
    J135-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    J135-8 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)