Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE INSTRUMENT SIDE PANEL LH


    B355333
  1. Using a moulding remover B, detach the 3 claws, 4 guides and remove the instrument side panel LH.



4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Operate the tilt lever to fully extend and raise the steering column.



    B355337E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 bolts <A>.

  1. Detach the 9 clips, 2 claws and remove the lower instrument panel finish panel sub-assembly LH.

  1. Disconnect each connector.



    B355336
  1. Detach the 3 hooks and disconnect the hood lock control lever from the lower instrument panel finish panel sub-assembly LH.



  1. Pull and slide the hood lock control cable, rotate the hood lock control cable, and then disconnect the hood lock control cable from the hood lock control lever.


    B355339



5. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



6. RELEASE PARKING BRAKE PEDAL


7. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C154230
  1. Remove the lock nut and adjustment nut.



    C154232
  1. Remove the clip.



    C155437
  1. Using a screwdriver, slowly bend up the claw.

    NOTICE:
    Be careful not to damage the No. 1 parking brake cable or claw.

  1. Disconnect the parking brake cable from the parking brake control pedal.



8. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. for 1GR-FE:
    Remove the front No. 2 exhaust pipe (Click here).

  1. for 1UR-FE:
    Remove the front No. 2 exhaust pipe (Click here).

  1. for 3UR-FE:
    Remove the front No. 2 exhaust pipe (Click here).

  1. for 3UR-FBE:
    Remove the front No. 2 exhaust pipe (Click here).



9. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for 3220 mm [10 ft. 6.8 in.] Wheelbase Type)
  1. Remove the adjustment nut and lock nut (labeled A).

  1. Remove the bolt (labeled B) and cable retainer.

  1. Remove the nut (labeled C) and clamp from the body.

  1. Disconnect the clamp (labeled D) from the No. 1 parking brake cable.

  1. Remove the 2 bolts (labeled E) and No. 1 parking brake cable from the inside of the vehicle.

    NOTICE:
    Do not bend and twist the parking brake cable.



  1. Remove the 3 bolts (labeled F) and No. 1 cable support bracket.


    C154241E01



10. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for 3700 mm [12 ft. 1.7 in.] Wheelbase Type)
  1. Remove the adjustment nut and lock nut (labeled A).

  1. Remove the bolt (labeled B) and cable retainer.

  1. Remove the 2 nuts (labeled C) and 2 clamps from the body.

  1. Disconnect the 2 clamps (labeled D) from the No. 1 parking brake cable.

  1. Remove the 2 bolts (labeled E) and No. 1 parking brake cable from the inside of the vehicle.

    NOTICE:
    Do not bend and twist the parking brake cable.



  1. Remove the 3 bolts (labeled F) and No. 1 cable support bracket.


    C154243E01



11. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for 4180 mm [13 ft. 8.6 in.] Wheelbase Type)
  1. Remove the adjustment nut and lock nut (labeled A).

  1. Remove the bolt (labeled B) and cable retainer.

  1. Remove the 3 nuts (labeled C) and 3 clamps from the body.

  1. Disconnect the 3 clamps (labeled D) from the No. 1 parking brake cable.

  1. Remove the 2 bolts (labeled E) and No. 1 parking brake cable from the inside of the vehicle.

    NOTICE:
    Do not bend and twist the parking brake cable.



  1. Remove the 3 bolts (labeled F) and No. 1 cable support bracket.


    C154242E01



12. REMOVE REAR WHEEL LH


13. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH


    C158344
  1. Remove the 2 bolts and disconnect the rear disc brake cylinder.

    NOTICE:
    1. Do not disconnect the flexible hose from the disc brake cylinder.
    2. Do not twist or bend the flexible hose.

  1. Hang the disc brake cylinder with a piece of wire.



14. REMOVE REAR DISC LH


    C155452E01
  1. Put matchmarks on the rear disc and axle hub if planning to reuse the disc.



    C155453
  1. Turn the shoe adjuster until the disc turns freely, and then remove the disc.



15. REMOVE PARKING BRAKE SHOE RETURN SPRING LH


    C179358E01
  1. Using SST, remove the return spring.

    SST
    09703-30011  



16. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY LH


    C155124E01
  1. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring pin.

    SST
    09718-00011  

  1. Disconnect the tension spring.

  1. Remove the No. 1 parking brake shoe and shoe adjuster screw set.



17. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY LH


    C154249E01
  1. Using SST, remove the shoe hold down spring cup, compression spring and shoe hold down spring pin.

    SST
    09718-00011  

  1. Remove the No. 2 parking brake shoe.



18. REMOVE PARKING BRAKE SHOE LEVER LH


    C155125
  1. Disconnect the No. 3 parking brake cable from the parking brake shoe lever.

  1. Remove the parking brake shoe lever.



19. REMOVE INTERMEDIATE LEVER TENSION SPRING


    C156990
  1. Remove the tension spring.



20. REMOVE NO. 2 CABLE RETAINER


    C156991
  1. Remove the bolt and cable retainer.



21. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


  1. Remove the 5 bolts and disconnect the No. 3 parking brake cable from the intermediate lever.

    NOTICE:
    Do not bend and twist the parking brake cable.



    C154245



    C154244
  1. Remove the bolt and No. 3 parking brake cable from the rear axle carrier.



22. REMOVE REAR WHEEL RH


23. DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



24. REMOVE REAR DISC RH

HINT:
Use the same procedures described for the LH side.



25. REMOVE PARKING BRAKE SHOE RETURN SPRING RH

HINT:
Use the same procedures described for the LH side.



26. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



27. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



28. REMOVE PARKING BRAKE SHOE LEVER RH

HINT:
Use the same procedures described for the LH side.



29. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY
  1. Disconnect the No. 2 parking brake cable from the 2 clamps (labeled A).

  1. Remove the 5 bolts (labeled B) and disconnect the No. 2 parking brake cable from the intermediate lever (labeled C).

    NOTICE:
    Do not bend and twist the parking brake cable.



  1. Remove the bolt (labeled D) and clamp.


    C154246E01



    C156832
  1. Remove the bolt and No. 2 parking brake cable from the rear axle carrier.



30. REMOVE PARKING BRAKE INTERMEDIATE LEVER SUB-ASSEMBLY


    C156999E01
  1. Remove the 2 bolts and intermediate lever with bracket.

  1. Remove the clip, washer, pin and intermediate lever from the bracket.



31. REMOVE NO. 2 CABLE SUPPORT BRACKET


    C159288
  1. Remove the 2 bolts and bracket.