ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT NO. 2 ENGINE MOUNTING BRACKET LH |
Install the front No. 2 engine mounting bracket LH with the bolt.
| 2. INSTALL ENGINE HANGER |
![]() |
Install 2 engine hangers with 4 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-31110 |
| No. 2 Engine Hanger | 12282-31140 |
| Bolt | 91671-C0830 |
| 3. REMOVE ENGINE FROM ENGINE STAND |
Attach an engine sling device and hang the engine with a chain block.
Lift the engine and remove it from the engine stand.
| 4. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine into the engine compartment.
![]() |
Install the front engine mounting insulator LH with the nut and 2 bolts.
![]() | Nut |
![]() | Bolt |
Install the front engine mounting insulator RH with the nut and 2 bolts.
Remove the 2 engine hangers and 4 bolts.
| 5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
![]() |
Install the front spacer, drive plate and rear spacer to the crankshaft.
| *1 | Front Spacer |
| *2 | Drive Plate and Ring Gear |
| *3 | Rear Spacer |
![]() | Automatic Transmission Side |
Clean the bolts and bolt holes.
![]() |
Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.
| *1 | Adhesive |
![]() |
Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.
| 6. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
| 8. INSTALL PROPELLER SHAFT ASSEMBLY |
| 9. CONNECT NO. 1 AND NO. 2 FUEL PIPES |
Connect the No. 1 and No. 2 fuel pipes (Click here).
Install the No. 2 fuel pipe clamp to the fuel tube connector.
| 10. CONNECT HEATER WATER HOSE ASSEMBLY |
![]() |
Connect the heater water inlet and outlet hoses.
| *a | Top |
Attach the wire harness clamp.
| 11. CONNECT COOLER COMPRESSOR ASSEMBLY |
Install the cooler compressor with the 2 stud bolts.
![]() |
Install the 2 bolts and 2 nuts.
Connect the cooler compressor connector.
| 12. CONNECT ENGINE WIRE |
Attach the 2 claws and connect the 2 connectors to connect the engine room junction block connector to the engine room junction block.
Attach the claw and install the bolt to connect the engine wire harness.
Attach the clamp and connect the air pump connector.
Install the ground cable with the 2 bolts.
Attach the clamp and connect the ECM connector (Click here).
Attach the 2 clamps and connect the 7 connectors to connect the junction block connector to the junction block.
Install the junction block cover.
Attach the 2 wire harness clamps.
Connect the 2 air injection control driver connectors.
| 13. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
Turn the crankshaft to gain access to the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.
Install the flywheel housing side cover.
| 14. INSTALL STARTER ASSEMBLY (for 1.6 kW Type) |
Install the starter with the 2 bolts.
Connect the starter wire with the nut.
Install the terminal cap.
Connect the starter connector.
Connect the ground wire with the bolt.
| 15. INSTALL STARTER ASSEMBLY (for 1.4 kW Type) |
Install the starter with the 2 bolts.
Connect the starter wire with nut.
Connect the starter connector.
Connect the ground wire with the bolt.
| 16. INSTALL STARTER COVER (for 1.4 kW Type) |
Install the starter cover with the 3 bolts.
| 17. INSTALL GENERATOR ASSEMBLY |
Install the generator bracket to the generator with the bolt.
Install the generator with the 2 bolts.
Install the generator bracket with the bolt.
Attach the wire harness clamp.
Connect the wire harness bracket with the bolt.
Connect the generator connector to the generator.
Install the generator wire with the nut.
Close the terminal cap.
| 18. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket to the cylinder head.
| *1 | Protrusion |
![]() | Front |
![]() |
Temporarily install the manifold with the new nut labeled 1.
Install the remaining 5 new nuts and tighten the nuts in the sequence shown in the illustration.
| 19. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
Install the heat insulator with the 3 bolts.
| 20. INSTALL NO. 2 AIR TUBE |
![]() |
Install 2 new gaskets to the No. 2 air tube as shown in the illustration.
| *1 | New Gasket |
| *2 | No. 2 Air Tube |
Install the No. 2 air tube with the 2 bolts and 2 nuts.
| 21. INSTALL MANIFOLD STAY |
Install the manifold stay with the 3 bolts.
| 22. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head.
| *1 | Protrusion |
![]() | Front |
![]() |
Temporarily install the manifold with the new nut labeled 1.
Install the remaining 5 new nuts and tighten the nuts in the sequence shown in the illustration.
| 23. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
Install the heat insulator with the 3 bolts.
| 24. INSTALL AIR TUBE |
![]() |
Install 2 new gaskets to the air tube as shown in the illustration.
| *1 | New Gasket |
| *2 | Air Tube |
Install the air tube with the 2 bolts and 2 nuts.
| 25. INSTALL NO. 2 MANIFOLD STAY |
Install the manifold stay with the 3 bolts.
Connect the wire harness connector.
| 26. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts.
Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector and attach the 2 clamps.
| 27. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
Connect the front No. 2 exhaust pipe to the exhaust pipe support.
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.
Install a new gasket and the front No. 2 exhaust pipe to the center exhaust pipe with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector.
| 28. CONNECT VANE PUMP ASSEMBLY |
Connect the vane pump with the 2 bolts.
Attach the wire harness clamp.
Connect the connector.
| 29. INSTALL FAN AND GENERATOR V BELT |
![]() |
Set the V belt onto every part.
| *1 | Vane Pump |
| *2 | Water Pump |
| *3 | No. 2 Idler |
| *4 | Generator |
| *5 | Cooler Compressor |
| *6 | No. 1 Idler |
| *7 | Crankshaft |
| *8 | V-ribbed Belt Tensioner |
While turning the belt tensioner counterclockwise, remove the pin.
![]() |
Check that the belt fits properly in the ribbed grooves.
| *1 | CORRECT |
| *2 | INCORRECT |
| 30. INSTALL INTAKE AIR SURGE TANK |
Install a new gasket to the intake air surge tank.
![]() |
Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.
| *1 | Nut |
Install the throttle body bracket with the 2 bolts.
Install the No. 1 surge tank stay with the 2 bolts.
Attach the wire harness clamp.
Install the No. 2 surge tank stay with the 2 bolts.
![]() |
Connect the No. 1 ventilation hose.
Connect the vacuum hose.
Connect the No. 1 fuel feed hose.
| *a | Front |
| *b | Matchmark |
| *c | Top |
![]() |
Connect the throttle body connector.
Connect the No. 4 water by-pass hose.
Connect the No. 5 water by-pass hose.
Connect the 2 heater hose clamps.
| *a | Front |
| *b | Matchmark |
| *c | RH |
| 31. INSTALL AIR TUBE ASSEMBLY |
![]() |
for Bank 1 Side:
Align the paint mark with the projection and connect the air tube assembly to the emission control valve set.
| *1 | Projection |
| *2 | Paint Mark |
| *a | Upper |
| *b | RH Side |
![]() |
for Bank 2 Side:
Align the paint mark with the projection and connect the air tube assembly to the No. 2 emission control valve set.
| *1 | Paint Mark |
| *2 | Projection |
| *a | Upper |
| *b | LH Side |
Install the 3 bolts.
Install the wire harness clamp bracket with the bolt.
Attach the 3 wire harness clamps to the intake air surge tank and bracket.
Connect the purge VSV connector.
![]() |
Connect the air injection system hose to the air tube assembly shown in the illustration.
| *1 | Paint Mark |
| *2 | Projection |
| *a | Upper |
| *b | LH Side |
| 32. INSTALL RADIATOR ASSEMBLY |
![]() |
Set the radiator bracket hooks to the radiator support holes.
Install the radiator assembly with the 4 bolts.
Install the 3 clips to connect the radiator side deflector LH.
Install the 3 clips to connect the radiator side deflector RH.
| 33. INSTALL FAN SHROUD |
Install the fan pulley to the water pump assembly.
Place the fan shroud together with the fan with fluid coupling between the radiator assembly and engine.
![]() |
Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fan with fluid coupling to the water pump assembly.
| *1 | Paint Mark |
Temporarily install the fan with fluid coupling to the water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the 2 claws of the fan shroud to the radiator assembly as shown in the illustration.
Install the fan shroud with the 2 bolts.
Connect the reservoir hose to the radiator tank upper.
Install the fan and generator V-belt .
Tighten the 4 nuts of the fan with fluid coupling.
| 34. INSTALL RADIATOR HOSE OUTLET |
![]() |
Connect the radiator hose outlet to the water inlet housing, and slide the clamp to secure the hose shown in the illustration.
| *a | Upper |
| *b | Front |
![]() |
Install the radiator hose outlet to the radiator assembly, and slide the clamp to secure the hose shown in the illustration.
| *a | Upper |
| *b | RH |
| 35. INSTALL RADIATOR HOSE INLET |
![]() |
Connect the radiator hose inlet, and slide the 2 clamps to secure the hose as shown in the illustration.
| *a | Upper |
| *b | LH |
| *c | Front |
| 36. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
Install the air cleaner case with the 2 bolts.
Attach the wire harness clamp.
Install the air cleaner filter element.
| 37. INSTALL AIR CLEANER CAP AND HOSE |
![]() |
Install the air cleaner cap and hose.
| *a | Top |
| *b | Front |
| *c | RH Side |
| *d | Align cutout portion of hose with protrusion of throttle |
| *e | Paint Mark |
Attach the 4 hook clamps to install the air cleaner cap and hose.
Tighten the clamp.
Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.
| 38. ADD ENGINE COOLANT |
Add engine coolant.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Install the radiator cap.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3
Repeat steps *1, *2 and *3 until the coolant level does not decrease.
Install the radiator cap.*4
Set the air conditioning as follows.*5
| Item | Condition |
| Fan speed | Any setting except off |
| Temperature | Toward WARM |
| Air conditioning switch | Off |
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6
Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7
If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8
If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
If the coolant level is below the FULL line, repeat steps *4 through *8.
If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.
| 39. ADD ENGINE OIL |
![]() |
Add fresh oil.
| Oil grade | Oil Viscosity (SAE) |
| ILSAC GF-5 multigrade engine oil | 0W-20 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| Drain and refill with oil filter change | 6.1 liters (6.4 US qts, 5.4 Imp. qts) |
| Dry fill | 7.0 liters (7.4 US qts, 6.2 Imp. qts) |
| 40. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY |
Install the front cowl top outer panel with the 7 bolts.
Connect the washer hose.
| 41. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
| 42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 43. INSPECT FOR FUEL LEAK |
Make sure that there are no fuel leaks after performing maintenance on the fuel system.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no leaks from the fuel system.
If there are fuel leaks, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.
| 44. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 45. INSPECT FOR EXHAUST GAS LEAK |
| 46. CHECK ENGINE OIL LEVEL |
Warm up the engine, and then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 47. INSTALL FRONT FENDER APRON SEAL REAR RH |
Install the fender apron seal with the 5 clips.
| 48. INSTALL FRONT FENDER APRON SEAL REAR LH |
Install the fender apron seal with the 5 clips.
| 49. INSTALL FRONT FENDER APRON SEAL RH |
Install the front fender apron seal with the 6 clips.
| 50. INSTALL FRONT FENDER APRON SEAL LH |
Install the front fender apron seal with the 6 clips.
| 51. PERFORM RESET MEMORY |
| 52. INSPECT IGNITION TIMING |
Warm up the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.
Inspect the ignition timing during idling.
Check that the ignition timing advances immediately when the engine speed is increased.
![]() |
When not using the Techstream:
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Inspect the ignition timing during idling.
Remove SST from the DLC3.
Inspect the ignition timing during idling.
Disconnect the timing light from the engine.
| 53. INSPECT ENGINE IDLE SPEED |
Warm up the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Inspect the engine idle speed.
![]() |
When not using the Techstream:
Connect SST to terminal 9 (TAC) of the DLC3.
| *a | Front view of DLC3 |
Race the engine at 2500 rpm for approximately 90 seconds.
Inspect the engine idle speed.
| 54. INSPECT CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.
Immediately check the CO/HC concentration during idling and/or at 2500 rpm.
If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.
Check the air fuel ratio sensor operation (Click here) and heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.
| CO | HC | Symptom | Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 55. INSTALL HOOD SUB-ASSEMBLY |
Install the hood with the 4 bolts and 2 clips.
| 56. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Adjust the hood sub-assembly position.
Loosen the 4 hinge bolts.
Move the hood sub-assembly and adjust the clearance between the hood sub-assembly and front fender.
Tighten the 4 hinge bolts after the adjustment.
![]() |
Adjust the cushion rubber so that the height of the hood sub-assembly and fender are aligned.
Adjust the hood lock assembly.
![]() |
Using a screwdriver, remove the hood lock nut cap as shown in the illustration.
| *1 | Protective Tape |
![]() |
Loosen the 2 bolts and hood lock bolt.
Adjust the hood lock assembly position so that the striker can enter it smoothly.
Tighten the bolts after the adjustment.
Install a new hood lock nut cap.
| 57. INSTALL RADIATOR GRILLE SUB-ASSEMBLY |