Home › TRANSMISSION · A760F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2772    Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

for Preparation Click here


DESCRIPTION

The ECM detects the signal from the transfer indicator switch.
This DTC indicates that the transfer indicator switch (L4) remains on.

DTC Code
DTC Detection Condition
Trouble Area
P2772
Transfer indicator switch (L4) remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in 2WD or 4H.
  1. Short in transfer indicator switch (L4) circuit
  2. 4 wheel drive control ECU
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the transfer-case transfer indicator switch to determine when the transfer-case 4L gears are engaged. If the transfer-case 4L gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the transfer indicator switch, illuminate the MIL and store the DTC:
  1. The transfer indicator switch indicates that the 4L transfer-case gears are engaged.
  2. The transfer-case shifter is in the "2WD" or "4H" position.
  3. The transfer-case output shaft speed is between 1000 and 3000 rpm.
  4. The specified time period has elapsed.

MONITOR STRATEGY


Related DTCs
P2772: Transfer indicator switch/Functional check
Required sensors/Components
Transfer indicator switch
Frequency of operation
Continuous
Duration
ON malfunction (A): 1.8 seconds
ON malfunction (B): 0.5 seconds
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0500 (Vehicle speed sensor "A" circuit)
Output speed sensor circuit
Not circuit malfunction
Transfer neutral position switch
OFF

ON Malfunction (A) 
Output speed (Transfer output speed)
1000 to 3000 rpm

ON Malfunction (B) 
Output speed (Transfer output speed)
143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunction (A) and (B)

ON Malfunction (A) 
Transfer indicator switch (L4)
ON

ON Malfunction (B) 
Actual transfer gear ratio
Transfer input speed / Transfer output speed
0.9 or more, and less than 1.1

WIRING DIAGRAM


C292708E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK TRANSFER INDICATOR SWITCH


    C292718E01
  1. Disconnect the D70 transfer indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D70-2 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transfer Indicator Switch)



NG
Go to step 2
OK

GO TO TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM (Click here)  

2.CHECK 4 WHEEL DRIVE CONTROL ECU


    C292717E01
  1. Disconnect the D70 transfer indicator switch connector.

  1. Disconnect the A26 4 wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-13 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to 4 Wheel Drive Control ECU)



NG
Go to step 3
OK

GO TO TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM (Click here)  

3.CHECK ECM


    C197708E33
  1. Disconnect the D70 transfer indicator switch connector.

  1. Disconnect the A26 4 wheel drive control ECU connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-21 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - 4 WHEEL DRIVE CONTROL ECU, TRANSFER INDICATOR SWITCH)
OK

REPLACE ECM (Click here)