Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is output when the combination meter detects the fuel sender gauge malfunction via the CAN.

DTC Code
DTC Detection Condition
Trouble Area
B1500
When combination meter detects fuel sender gauge malfunction
  1. Harness or connector
  2. Combination meter
  3. Fuel sender gauge
  4. Fuel suction with pump and gauge tube

WIRING DIAGRAM


B166182E05


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (FUEL SENDER GAUGE)
  1. Operate the Techstream according to the display and select the "Data List" (Click here).

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Level
    Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5
    Fuel sender input value
    Unit: L

    OK:
    Fuel value displayed on Techstream is almost same as needle indication



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND GAUGE TUBE AND BODY GROUND)
E146742E06
  1. Disconnect the J28 meter connector.

  1. Disconnect the R6 gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J28-26 (L) - R6-2
    Always
    Below 1 Ω
    J28-25 (E3) - R6-3
    J28-24 (ES) - Body ground
    J28-26 (L) or R6-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FUEL SENDER GAUGE ASSEMBLY
E282500E01
  1. Remove the fuel sender gauge.

    1. for 1GR-FE (Click here)
    2. for 1UR-FE (Click here)
    3. for 3UR-FE (Click here)
    4. for 3UR-FBE (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    12 to 18 Ω
    Float level is E (lower)
    405 to 415 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1UR-FE)
    C
    NG (for 3UR-FE)
    D
    NG (for 3UR-FBE)
    E



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E158805E20
  1. Remove the fuel suction with pump and gauge tube.

    1. for 1GR-FE (Click here)
    2. for 1UR-FE (Click here)
    3. for 3UR-FE (Click here)
    4. for 3UR-FBE (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2 - B2
    Always
    Below 1 Ω
    A3 - B1

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 1UR-FE)
    C
    NG (for 3UR-FE)
    D
    NG (for 3UR-FBE)
    E



B
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

C
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

D
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)

E
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)