Home › ENGINE ยท 3UR-FE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151835E01

  1. Tighten the radiator drain cock plug by hand.



6. REMOVE RADIATOR ASSEMBLY
(Click here)


7. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



8. REMOVE AIR CLEANER ASSEMBLY


    A309637E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. for Type A:
      Unfasten the 4 hook clamps and then remove the air cleaner cap.

    4. for Type B:
      Unfasten the 2 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A309638E01
  1. Remove the 2 bolts and air cleaner case.



9. DISCONNECT ENGINE WIRE


  1. Engine Room LH Side:



      A162560
    1. Remove the engine room relay block cover.

    2. Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.



    3. A153551
    4. Disconnect the 4 air injection control driver connectors.



    5. A163944
    6. Disconnect the 2 wire harness clamps.



    7. A259655
    8. Disconnect the injector connector.

    9. Disconnect the 4 ignition coil connectors.

    10. Disconnect the 2 VVT sensor connectors.

    11. Disconnect the 5 clamps.

    12. Remove the 2 bolts and ground wire LH.



    13. A162562
    14. Disconnect the engine coolant temperature sensor connector.

    15. Disconnect the 2 camshaft timing oil control valve connectors.

    16. Disconnect the camshaft position sensor connector.

    17. Disconnect the 3 clamps.

    18. Disconnect the cooler compressor connector.



    A264086
  1. Engine Room RH Side:

    1. Disconnect the 2 camshaft timing oil control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the injector connector.

    4. Disconnect the 2 VVT sensor connectors.

    5. Remove the 2 bolts and ground wire RH.

    6. Disconnect the 2 air pump connectors.

    7. Disconnect the throttle position sensor and throttle control motor connector.

    8. Disconnect the 7 clamps.



    A162564E02
  1. Disconnect the 2 clamps and power steering oil pressure switch connector.
    Text in Illustration 
    *1
    Junction Connector

  1. for 4WD:
    Disconnect the clamp and junction connector.



10. REMOVE INTAKE MANIFOLD
(Click here)


11. DISCONNECT AIR PUMP HOSE AND WIRE HARNESS


    A163452E02
  1. Slide the 2 clamps and disconnect the No. 2 air hose and No. 3 air hose from the air tube sub-assembly.
    Text in Illustration 
    *1
    No. 3 Air Hose
    *2
    No. 2 Air Hose

  1. Disconnect the 2 clamps.



12. DISCONNECT HEATER HOSE AND PIPE


    A163380
  1. Remove the 2 bolts.

  1. Slide the 3 clamps and disconnect the 3 hoses.



13. DISCONNECT COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



14. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    A165142E05
  1. Remove the 2 bolts and disconnect the No. 2 fuel tube sub-assembly.
    Text in Illustration 
    *a
    LH Side
    *b
    RH Side



15. REMOVE OIL FILTER ELEMENT


    A094910E01
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.



    A162459
  1. Remove the oil filter drain plug.



    A162460
  1. Install the pipe to the oil filter cap.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A162461
  1. Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.



    A162462E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A162463
  1. Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



16. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY


    A163657
  1. Disconnect the sender gauge connector.



    A162467
  1. Remove the oil pressure sender gauge.



17. REMOVE NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)


    A165547
  1. Slide the 4 clamps and disconnect the 4 hoses from the No. 2 water by-pass pipe.

  1. Remove the 3 bolts and No. 2 water by-pass pipe.



18. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)


    A163672
  1. Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.



19. REMOVE OIL FILTER BRACKET (w/ Oil Cooler)


    A162469
  1. Remove the 2 bolts, 2 nuts and filter bracket.



    A162470
  1. Remove the 2 O-rings.



20. REMOVE OIL FILTER BRACKET (w/o Oil Cooler)


    A163541
  1. Remove the 2 bolts, 2 nuts and oil filter bracket.



    A162470
  1. Remove the 2 O-rings.



21. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



22. DISCONNECT VANE PUMP ASSEMBLY


    A163289
  1. Remove the 2 bolts and disconnect the vane pump assembly.



23. REMOVE GENERATOR ASSEMBLY


    A163292
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.



    A163290
  1. Remove the bolt and disconnect the wire harness bracket from the generator assembly.



    A163293
  1. Remove the 2 bolts, 2 nuts and generator assembly.

  1. Remove the 2 stud bolts.



24. REMOVE NO. 1 WATER BY-PASS HOSE


    A308519
  1. Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.



25. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162550
  1. Remove the bolt and disconnect the air tube sub-assembly.



    A162551
  1. Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.

  1. Remove the 2 bolts and water by-pass pipe sub-assembly.



26. DISCONNECT NO. 9 WATER BY-PASS HOSE


    A291559E02
  1. Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.
    Text in Illustration 
    *1
    No. 9 Water By-pass Hose
    *2
    No. 10 Water By-pass Hose



27. DISCONNECT NO. 10 WATER BY-PASS HOSE
  1. Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.



28. REMOVE FRONT WATER BY-PASS JOINT


    A291566
  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.

  1. Remove the 4 nuts, front water by-pass joint and 2 gaskets.



29. REMOVE NO. 2 ENGINE COVER


A307666


30. REMOVE NO. 1 ENGINE COVER


A158581


31. REMOVE AIR TUBE SUB-ASSEMBLY


    A162553
  1. Remove the bolt, disconnect the 2 hoses, and remove the air tube sub-assembly.



32. REMOVE WATER INLET HOUSING


    A162554
  1. Remove the 3 bolts, water inlet housing and gasket.



33. REMOVE WATER PUMP PULLEY


    A162556E03
  1. Using SST, hold the water pump pulley.
    Text in Illustration 
    *a
    SST

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



34. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



35. REMOVE FAN BRACKET ASSEMBLY


    A162558
  1. Remove the 4 bolts and fan bracket assembly.



36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.



37. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 8 bolts and 8 ignition coils.



38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.



39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.



40. REMOVE CRANKSHAFT PULLEY


    A164228E05
  1. Using SST, loosen the crankshaft pulley set bolt.
    Text in Illustration 
    *a
    SST
    *b
    Turn
    *c
    Hold

    SST
    09213-70011  
    09330-00021  

  1. Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.



    A164229E04
  1. Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.
    Text in Illustration 
    *a
    SST
    *b
    Turn
    *c
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)



41. DISCONNECT WIRE HARNESS CLAMP BRACKET


    A163733
  1. Remove the bolt and disconnect the wire harness clamp bracket.



42. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A162529E02
  1. Remove the 28 bolts and nut shown in the illustration.
    Text in Illustration 
    *1
    Nut



    A162530
  1. Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan sub-assembly.



43. REMOVE WATER INLET PIPE


    A162532
  1. Remove the water inlet pipe from the No. 1 heat exchanger cover.

  1. Remove the 2 O-rings from the water inlet pipe.