DTC B1424/24 Solar Sensor Circuit (Driver Side) |

| DTC Code | DTC Detection Condition | Trouble Area |
| B1424/24 | Open or short in driver side solar sensor circuit |
|

| 1.READ VALUE USING TECHSTREAM (SOLAR SENSOR (for Driver Side)) |
Use the Data List to check if the driver side solar sensor is functioning properly.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Solar Sensor (D Side) | Driver side solar sensor / Min.: 0 Max.: 255 | Driver side solar sensor voltage increases as brightness increases | Open in circuit: 0 Short in circuit: 255 |
| Result | Proceed to |
| NG | A |
| OK (Checking from the PROBLEM SYMPTOMS TABLE) | B |
| OK (Checking from the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR) |
![]() |
Disconnect the J128 solar sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J128-3 (CLTE) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J128-6 (CLTB) - J128-3 (CLTE) | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SOLAR SENSOR) |
![]() |
Disconnect the J19 air conditioning amplifier connector.
Disconnect the J128 solar sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J19-33 (TSD) - J128-1 (TSL) | Always | Below 1 Ω |
| J19-33 (TSD) or J128-1 (TSL) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSL - CLTE VOLTAGE)) |
![]() |
Remove the solar sensor with its connector still connected (Click here).
Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (TSL) - 3 (CLTE) | Sensor is subjected to electric light | 0.8 to 4.3 V |
| Sensor is covered with a cloth | Below 0.8 V |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR AND BODY GROUND) |
![]() |
Disconnect the J3 ECU connector.
Disconnect the J128 solar sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J3-18 (CLTE) - J128-3 (CLTE) | Always | Below 1 Ω |
| J3-20 (CLTB) - J128-6 (CLTB) | ||
| J3-18 (CLTE) or J128-3 (CLTE) - Body ground | Always | 10 kΩ or higher |
| J3-20 (CLTB) or J128-6 (CLTB) - Body ground |
|
| ||||
| OK | ||
| ||