SFI SYSTEM > Fuel Pump Control Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether operating sounds can be heard while operating the relay using the Techstream.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
Disconnect the R7 fuel pump ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R7-1 (FPC) - A24-52 (FPC) | Always | Below 1 Ω |
| R7-2 (DI) - A24-18 (DI) | Always | Below 1 Ω |
| R7-3 (E) - Body ground | Always | Below 1 Ω |
| R7-1 (FPC) or A24-52 (FPC) - Body ground | Always | 10 kΩ or more |
| R7-2 (DI) or A24-18 (DI) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 3.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 5.INSPECT CIRCUIT OPENING RELAY (C/OPN) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT CIRCUIT OPENING RELAY (POWER SOURCE VOLTAGE) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C/OPN relay (1) - Body ground | Ignition switch ON | 11 to 14 V |
| C/OPN relay (3) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - ECM AND FUEL PUMP ECU) |
Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).
Disconnect the A24 ECM connector.
Disconnect the R7 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (2) - A24-48 (FC) | Always | Below 1 Ω |
| C/OPN relay (5) - R7-4 (+B) | Always | Below 1 Ω |
| C/OPN relay (2) or A24-48 (FC) - Body ground | Always | 10 kΩ or higher |
| C/OPN relay (5) or R7-4 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU) |
Disconnect the R6 fuel pump connector.
Disconnect the R8 fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R6-4 (B) - R8-1 (FP) | Always | Below 1 Ω |
| R6-5 (E) - R8-2 (FP-) | Always | Below 1 Ω |
| R6-4 (B) or R8-1 (FP) - Body ground | Always | 10 kΩ or higher |
| R6-5 (E) or R8-2 (FP-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT FUEL PUMP |
Inspect the fuel pump .
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM AND BODY GROUND) |
Disconnect the R7 fuel pump ECU connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R7-1 (FPC) - A24-52 (FPC) | Always | Below 1 Ω |
| R7-2 (DI) - A24-18 (DI) | Always | Below 1 Ω |
| R7-3 (E) - Body ground | Always | Below 1 Ω |
| R7-1 (FPC) or A24-52 (FPC) - Body ground | Always | 10 kΩ or more |
| R7-2 (DI) or A24-18 (DI) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 11.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY - FUEL PUMP RELAY AND IGN FUSE) |
![]() |
Remove the circuit opening relay (C/OPN) from the engine room relay block (Click here).
Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).
Remove the IGN fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C/OPN relay (1) - IGN fuse (2) | Always | Below 1 Ω |
| C/OPN relay (3) - F/PMP relay (3) | Always | Below 1 Ω |
| C/OPN relay (1) or IGN fuse (2) - Body ground | Always | 10 kΩ or more |
| C/OPN relay (3) or F/PMP relay (3) - Body ground | Always | 10 kΩ or more |
|
| ||||
| OK | |
| 14.INSPECT FUEL PUMP RELAY (F/PMP) |
![]() |
Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (FUEL PUMP RELAY - INTEGRATION RELAY, BATTERY AND BODY GROUND) |
![]() |
Remove the F/PMP fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F/PMP fuse | Always | Below 1 Ω |
Reinstall the F/PMP fuse.
Remove the fuel pump relay (F/PMP) from the engine room relay block (Click here).
Remove the integration relay from the engine room relay block (Click here).
Disconnect the 1B integration relay connector.
Disconnect the cable from the battery positive (+) terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F/PMP relay (1) - 1B-4 | Always | Below 1 Ω |
| F/PMP relay (5) - Positive (+) battery cable | Always | Below 1 Ω |
| F/PMP relay (2) - Body ground | Always | Below 1 Ω |
| F/PMP relay (1) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| F/PMP relay (5) or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||