Home › DRIVE LINE › WF1AM TRANSFER › TRANSFER CASE REAR OIL SEAL

TRANSFER CASE REAR OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL
  1. Remove the lower transfer case protector .



    C291184E01
  1. Remove the transfer case plug (filler) and transfer case plug (drain), and drain the transfer oil.
    Text in Illustration 
    *1
    Transfer Case Plug (Filler)
    *2
    Transfer Case Plug (Drain)



2. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


3. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (REAR)


    C291146E01
  1. Using a chisel and hammer, loosen the staked part of the transfer output shaft nut.

    NOTICE:
    1. Completely loosen the staked part of the transfer output shaft nut when removing it.
    2. Do not damage the threads of the rear transfer output shaft.

  1. Using SST, hold the output shaft companion flange sub-assembly (rear).

    SST
    09330-00021  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using a 30 mm socket wrench, remove the transfer output shaft nut.

  1. Remove the O-ring.



    C291147E01
  1. Using SST, remove the output shaft companion flange sub-assembly (rear).

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



4. REMOVE TRANSFER OUTPUT SHAFT TYPE T OIL SEAL


    C291148E01
  1. Using SST, remove the transfer output shaft type T oil seal.

    SST
    09308-10010  

    NOTICE:
    Be careful not to damage the transfer output shaft type T oil seal and rear transfer case contact surface.



5. INSTALL TRANSFER OUTPUT SHAFT TYPE T OIL SEAL
  1. Apply Toyota Genuine Transfer gear oil LF 75W or equivalent to the spline area of the rear transfer output shaft.



    C291185E01
  1. Using SST and a hammer, tap in a new transfer output shaft type T oil seal as shown in the illustration.

    SST
    09502-12010  
    09513-36040  

    Drive in depth (A):
    1.4 to 2.4 mm (0.056 to 0.094 in.)



6. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (REAR)
  1. Install the output shaft companion flange sub-assembly (rear) onto the rear transfer output shaft.



    C291217E01
  1. Using SST, hold the output shaft companion flange sub-assembly (rear).

    SST
    09330-00021  

  1. Using a 30 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1295 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E05
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *1
    Transfer Output Shaft Nut
    *2
    Rear Transfer Output Shaft
    *a
    Correct
    *b
    Incorrect



7. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


8. ADD TRANSFER OIL
  1. Install a new transfer case plug (drain).

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Add oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the transfer case plug (filler) hole.

    NOTICE:
    1. Add oil slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new transfer case plug (filler).

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Install the lower transfer case protector .



9. CHECK TRANSFER OIL


    C291183
  1. Remove the transfer case plug (filler).



    C083746E10
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the transfer case plug (filler) hole.
    If the result is not as specified, add Toyota Genuine Transfer gear oil LF 75W or equivalent.
    Text in Illustration 
    *a
    0 to 5.0 mm (0 to 0.196 in.)

    Viscosity:
    SAE 75W

    Standard Capacity:
    1.4 to 1.5 liters (1.48 to 1.58 US qts., 1.24 to 1.32 Imp. qts.)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leaks.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new transfer case plug (filler).

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



10. CHECK FOR TRANSFER OIL LEAK