Home › ENGINE ยท 3UR-FE › EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here


HINT:
If an exhaust gas leak has been repaired, perform an inspection following the repair (Click here).



1. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162117E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162754E01
  1. Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



2. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A162119E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162115E01
  1. Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    A168654E01
  1. Align the matchmarks and insert the No. 2 intermediate shaft into the intermediate shaft.



    A168655E01
  1. Align the matchmarks and insert the No. 2 intermediate shaft into the power steering gear.

  1. Install the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



6. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


7. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
(Click here)


8. CONNECT COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor assembly with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor assembly.



9. INSTALL GENERATOR ASSEMBLY


    A260951
  1. Install the generator with the 3 bolts and nut.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



    A163292
  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.



    A163290
  1. Install the harness bracket to the generator with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



10. CONNECT VANE PUMP ASSEMBLY

HINT:
A163333E01
Before performing the following procedures, move the spacer until the vane pump can be installed.



    A163289
  1. Connect the vane pump to the timing chain cover with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    A164433
  1. Attach the 2 clamps and connect the power steering oil pressure switch connector.



11. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.



    A164434E01
  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.



12. INSTALL FAN SHROUD
  1. Install the fan pulley to the fan bracket.

  1. Place the fan shroud together with the fan with fluid coupling between the radiator assembly and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fan with fluid coupling to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A151820
  1. Attach the 2 claws of the fan shroud to the radiator assembly as shown in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A215580E01
  1. for Condenser with Integrated Oil Cooler:
    Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.

  1. Connect the reservoir hose to the upper radiator tank.

  1. Install the fan and generator V-belt.



    A151842
  1. Tighten the 4 nuts of the fan with fluid coupling.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



13. INSTALL FAN AND GENERATOR V-BELT


    A163771E01
  1. Set the V belt onto every part.

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly set to each pulley.



    A174124E01
  1. After installing the belt, check that it fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



14. CONNECT OUTLET RADIATOR HOSE


15. CONNECT INLET RADIATOR HOSE


16. INSTALL AIR CLEANER ASSEMBLY


    A309638E01
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element onto the air cleaner case.



    A309637E01
  1. Install the air cleaner cap.

    1. for Type A:
      Install the air cleaner cap and fasten the 4 hook clamps.

    2. for Type B:
      Install the air cleaner cap and fasten the 2 hook clamps.

    3. Connect the MAF meter connector.

    4. Attach the wire harness clamp.



17. INSTALL AIR CLEANER HOSE ASSEMBLY
  1. Install the air cleaner hose assembly with the 2 hose clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose to the air cleaner hose assembly.

  1. Connect the ventilation hose to the air cleaner hose assembly, and slide the clamp to secure the hose.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


19. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard capacity: 
    Item
    Specified Condition
    w/ Trailer Towing System
    13.0 liters (13.7 US qts, 11.4 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



20. INSPECT FOR COOLANT LEAK


A161766

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



21. INSPECT FOR EXHAUST GAS LEAK

HINT:
If an exhaust gas leak has been repaired, perform an inspection following the repair (Click here).

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


22. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the fender apron seal with the 5 clips.



23. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the fender apron seal with the 6 clips.



24. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 5 clips.



25. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the fender apron seal with the 6 clips.



26. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



27. INSTALL V-BANK COVER SUB-ASSEMBLY


    A307791E01
  1. Attach the 2 V-bank cover hooks to the No. 1 V-bank cover bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover sub-assembly to attach the pins.
    Text in Illustration 
    *1
    V-bank Cover Grommet
    *2
    Pin
    *3
    No. 1 V-bank Cover Bracket
    *4
    V-bank Cover Hook