Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator sub-assembly consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch. This DTC is output when the ECU built into the regulator motor determines that the power window switch is stuck.

NOTICE:
  1. When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
  2. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
    (a) Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
    (b) Open the power window by fully pushing down the power window switch.


Master Switch 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator master switch is stuck.
  2. The power window regulator master switch is held in the same position for more than 20 seconds.
  1. Power window regulator master switch assembly
  2. Harness or connector
  3. Power window regulator master switch assembly held in same position for more than 20 seconds

Driver Side Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator master switch stuck.
  2. The power window regulator master switch is held in the same position for more than 20 seconds.
  1. Power window regulator master switch assembly
  2. Front power window regulator motor assembly LH
  3. Harness or connector
  4. Power window regulator master switch assembly held in same position for more than 20 seconds

Front Passenger Side Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
  1. The power window regulator switch is stuck.
  2. The power window regulator switch is held in the same position for more than 20 seconds.
  1. Power window regulator switch assembly
  2. Front power window regulator motor assembly RH
  3. Harness or connector
  4. Power window regulator switch assembly held in same position for more than 20 seconds

WIRING DIAGRAM


B178355E03


INSPECTION PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK DTC
  1. Check where DTC B2312 is output from.
    Result 
    Result
    Proceed to
    DTC B2312 output from power window regulator master switch assembly.
    A
    DTC B2312 output from front power window regulator motor assembly LH.
    B
    DTC B2312 output from front power window regulator motor assembly RH.
    C



B
Go to step 4

C
Go to step 6
A


3.READ VALUE USING TECHSTREAM (MASTER SWITCH)
  1. Use the Data List to check if the master switch is functioning properly.

    Master Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver side power window auto UP/DOWN switch signal / ON or OFF
    ON: Driver side switch of master switch operated
    OFF: Driver side switch of master switch not operated
    -
    P Door P/W Auto SW
    Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF
    ON: Front passenger side switch of master switch operated
    OFF: Front passenger side switch of master switch not operated
    -
    P Door P/W Up SW
    Front passenger side power window remote manual UP switch signal / ON or OFF
    ON: Front passenger side switch of master switch operated
    OFF: Front passenger side switch of master switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window remote manual DOWN switch signal / ON or OFF
    ON: Front passenger side switch of master switch operated
    OFF: Front passenger side switch of master switch not operated
    -
    Window Lock Switch Status
    Power window LOCK switch / ON or OFF
    ON: Power window lock switch in LOCK position
    OFF: Power window lock switch in UNLOCK position
    -

    OK:
    The Techstream display changes normally when master switch is operated.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE) 

4.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)
  1. Use the Data List to check if the driver side motor is functioning properly.

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver side power window auto UP/DOWN switch signal / ON or OFF
    ON: Driver side switch operated
    OFF: Driver side switch not operated
    -
    D Door P/W Up SW
    Driver side power window MANUAL UP switch signal / ON or OFF
    ON: Driver side switch operated
    OFF: Driver side switch not operated
    -
    D Door P/W Down SW
    Driver side power window MANUAL DOWN switch signal / ON or OFF
    ON: Driver side switch operated
    OFF: Driver side switch not operated
    -

    OK:
    The Techstream display changes normally when master switch is operated.



NG
Go to step 5
OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE) 

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)


    B191453E02
  1. Disconnect the N2 master switch connector.

  1. Disconnect the N12 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-4 (UP) - N12-10 (UP)
    Always
    Below 1 Ω
    N2-5 (DOWN) - N12-7 (DOWN)
    Always
    Below 1 Ω
    N2-4 (UP) - Body ground
    Always
    10 kΩ or higher
    N2-5 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

6.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
  1. Use the Data List to check if the front passenger side motor is functioning properly.

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto UP/DOWN switch signal / ON or OFF
    ON: Power window regulator switch assembly operated
    OFF: Power window regulator switch assembly not operated
    -
    P Door P/W Up SW
    Front passenger side power window manual UP switch signal / ON or OFF
    ON: Power window regulator switch assembly operated
    OFF: Power window regulator switch assembly not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual DOWN switch signal / ON or OFF
    ON: Power window regulator switch assembly operated
    OFF: Power window regulator switch assembly not operated
    -

    OK:
    The Techstream display changes normally when master switch is operated.



NG
Go to step 7
OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE) 

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B231347E02
  1. Remove the power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual UP operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual DOWN operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    AUTO UP/DOWN operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)


    B184455E15
  1. Disconnect the M10 switch connector.

  1. Disconnect the M11 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M10-6 (UP) - M11-10 (UP)
    Always
    Below 1 Ω
    M10-7 (DOWN) - M11-7 (DOWN)
    Always
    Below 1 Ω
    M10-8 (AUTO) - M11-4 (AUTO)
    Always
    Below 1 Ω
    M10-6 (UP) - Body ground
    Always
    10 kΩ or higher
    M10-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    M10-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)