Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2651    Reclining Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or rearward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2651
The forward and rearward lock detection position of the sensor is the same.
  1. Position control ECU and switch assembly
  2. Front seatback frame sub-assembly LH (reclining motor)
  3. Harness or connector

WIRING DIAGRAM


B352948E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SEAT RECLINING)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Driver Seat / Active Test.

  1. Perform the Active Test according to the display on the Techstream.

    Driver Seat 
    Tester Display
    Test Part
    Control Ranger
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)


    B352958E01
  1. Disconnect the front seatback frame sub-assembly LH (reclining motor) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z6-4 - Z6-3
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Seatback Frame Sub-assembly LH [Reclining Motor])



NG
Go to step 4
OK


3.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)


    B352959E01
  1. Reconnect the front seatback frame sub-assembly LH (reclining motor) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z6-4 - Body ground
    Reclining switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Front Seatback Frame Sub-assembly LH [Reclining Motor])



NG
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH (Click here)
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z10 position control ECU and switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-11 (SSRR) - Z6-4
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z6-3
    Always
    Below 1 Ω
    Z10-11 (SSRR) or Z6-4 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z6-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)  

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
  1. Remove the front seatback frame sub-assembly LH (reclining motor) (Click here).

  1. Inspect the front seatback frame sub-assembly LH (reclining motor) .



NG
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z9 position control ECU and switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z9-9 (RCL+) - Z6-2
    Always
    Below 1 Ω
    Z9-11 (RCL-) - Z6-1
    Always
    Below 1 Ω
    Z9-9 (RCL+) or Z6-2 - Body ground
    Always
    10 kΩ or higher
    Z9-11 (RCL-) or Z6-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)