DTC P006A MAP - Mass or Volume Air Flow Correlation Bank 1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P006A | After the engine is warmed up and the engine is idled for 30 seconds or more, the intake manifold pressure malfunction determination value is higher than the threshold value due to an intake leak. (1 trip detection logic) |
|
| Related DTCs | P006A: MAP - mass or volume air flow correlation |
| Required Sensors/Components (Main) |
|
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediately |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Time after engine start | 5 seconds |
| Engine coolant temperature | 70°C (158°F) or higher |
| Intake air temperature | 5.5°C (41.9°F) or higher |
| Atmospheric pressure | 76 kPa (570 mmHg) or higher |
| Engine load fluctuation (per 8 msec.) | 10% or less |
| VVT system | Stable |
| EGR valve | Closed |
| Engine speed | 250 to 2000 rpm |
| Engine load (normal operation) | 35% or less |
| Engine load (fail-safe) | 41% or less |
| Pressure correlation | 24 kPa (180 mmHg) or higher |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more.
Idle the engine for 30 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P006A | A |
| P006A and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE (HOSE CONNECTION) |
Check the PCV hose connections .
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks .
|
| ||||
| OK | |
| 4.READ VALUE USING TECHSTREAM (MAP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the MAP value.
| Engine Condition | Techstream Display |
| Ignition switch ON | 85 to 110 kPa (638 to 825 mmHg) |
|
| ||||
|
| ||||
| 5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor. (Click here).
| NEXT | |
| 6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | 20 to 40 kPa (150 to 300 mmHg) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 7.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve assembly is stuck open.
|
| ||||
| OK | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P006A) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTC (Click here).
Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off.
Idle the engine for 30 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P006A is output | A |
| No DTC output | B |
|
| ||||
| A | |
| 9.INSPECT MASS AIR FLOW METER |
Connect the Techstream to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
|
| ||||
| OK | ||
| ||