DTC P219A Bank 1 Air-Fuel Ratio Imbalance |
DTC P219B Bank 2 Air-Fuel Ratio Imbalance |
DTC P219C Cylinder 1 Air-Fuel Ratio Imbalance |
DTC P219D Cylinder 2 Air-Fuel Ratio Imbalance |
DTC P219E Cylinder 3 Air-Fuel Ratio Imbalance |
DTC P219F Cylinder 4 Air-Fuel Ratio Imbalance |
DTC P21A0 Cylinder 5 Air-Fuel Ratio Imbalance |
DTC P21A1 Cylinder 6 Air-Fuel Ratio Imbalance |
DTC P21A2 Cylinder 7 Air-Fuel Ratio Imbalance |
DTC P21A3 Cylinder 8 Air-Fuel Ratio Imbalance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P219A | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P219B | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P219C | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P219D | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P219E | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P219F | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P21A0 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P21A1 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P21A2 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| P21A3 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
|
| Related DTCs | P219A: Air fuel ratio cylinder imbalance monitor (Bank 1) P219B: Air fuel ratio cylinder imbalance monitor (Bank 2) P219C: Air fuel ratio cylinder imbalance monitor (Cylinder 1) P219D: Air fuel ratio cylinder imbalance monitor (Cylinder 2) P219E: Air fuel ratio cylinder imbalance monitor (Cylinder 3) P219F: Air fuel ratio cylinder imbalance monitor (Cylinder 4) P21A0: Air fuel ratio cylinder imbalance monitor (Cylinder 5) P21A1: Air fuel ratio cylinder imbalance monitor (Cylinder 6) P21A2: Air fuel ratio cylinder imbalance monitor (Cylinder 7) P21A3: Air fuel ratio cylinder imbalance monitor (Cylinder 8) |
| Required Sensors/Components (Main) | Air fuel ratio sensor Crankshaft position sensor |
| Required Sensors/Components (Related) | Mass air flow meter assembly Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: Air fuel ratio sensor open circuit between AF+ and AF- and low impedance 30 seconds: Crankshaft position sensor monitoring method |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (Camshaft timing oil control valve assembly bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust camshaft timing oil control valve assembly bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0015, P0025 (Exhaust VVT system bank 1, 2 - retard) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0401 (EGR system) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P1340 (Camshaft position sensor) P2440 - P2447 (Secondary air injection system) P0500 (Vehicle speed sensor) |
| Air fuel ratio sensor status | Activated |
| Engine speed | 1400 to 2200 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa (570 mmHg) or higher |
| Fuel system status | Closed loop |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Engine speed | 400 to 1000 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Air fuel ratio sensor status | Activated |
| Battery voltage | 11 V or higher |
| Fuel system status | Closed loop |
| A/F sensor monitoring method criteria | 0.15 or more |
| A/F sensor monitoring method criteria | 0.2 or more |
| Crankshaft position sensor monitoring method criteria | 1.0 or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output | A |
| DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Air Fuel Ratio Sensor Monitoring Method (P219A and P219B) | Crankshaft Position Sensor Monitoring Method (P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and P21A3) | Note |
| DTCs are output | DTC is output (Only one DTC relating to a single cylinder is output) | Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected. |
| DTCs are output | DTCs are output (Multiple DTCs relating to multiple cylinders are output) | Malfunction of cylinders except ones detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.*1 |
| DTCs are not output | DTCs are output | Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected. |
| DTCs are output | DTCs are not output | Malfunctioning of the bank detected by the Air Fuel Ratio Sensor Monitoring Method is primarily suspected. |
| NEXT | |
| 3.READ VALUE USING DTC OUTPUT |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Result | Proceed to |
| P219A or P219B is output | A |
| P219A or P219B, and P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3 is are output | B |
| DTC P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output |
|
| ||||
| A | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #8 Misfire Count.
Perform the Control the Injection Volume operation with the engine idling.
Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count") while decreasing the injection volume in 5% increments.
| NEXT | |
| 5.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 7.INSPECT SPARK PLUG |
Inspect the spark plug of the cylinder causing the imbalance .
|
| ||||
| OK | |
| 8.CHECK FOR SPARKS AND IGNITION |
Perform a spark test .
| NEXT | |
| 9.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE |
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
|
| ||||
| OK | |
| 11.CHECK FOR CAUSE OF FAILURE |
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
| NEXT | ||
| ||