DTC U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU) |
| DTC Code | DTC Detection Condition | Trouble Area |
| U1002 | Lost communication with the gateway module. |
|

| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
| NEXT | |
| 3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Resistance: Malfunction |
| J123-13 (CA2H) - J123-12 (CA2L) | Ignition switch off | 54 to 69 Ω | Below 53 Ω: Short in line |
| J123-13 (CA2H) - J123-12 (CA2L) | Ignition switch off | 54 to 69 Ω | Higher than 70 Ω: Open in CAN main bus line |
| J123-13 (CA2H) - J123-2 (BATT) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| J123-12 (CA2L) - J123-2 (BATT) | Ignition switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| J123-13 (CA2H) - J123-4 (GND) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| J123-12 (CA2L) - J123-4 (GND) | Ignition switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| *a | Component with harness connected (Network Gateway ECU) |
| Result | Proceed to |
NG
| A |
NG
| B |
| OK | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
![]() |
Disconnect the R17 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R17-1 (CANH) - R17-4 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector (to No. 4 Junction Connector) |
|
| ||||
| OK | |
| 5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R17-2 (CANH) - R17-3 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector (to No. 4 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 6.CONNECT CONNECTOR |
Reconnect the R17 No. 4 junction connector.
| NEXT | |
| 7.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU) |
![]() |
Disconnect the J123 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J123-13 (CA2H) - J123-12 (CA2L) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to Network Gateway ECU) |
|
| ||||
| OK | ||
| ||
| 8.CONNECT CONNECTOR |
Reconnect the R17 No. 4 junction connector.
| NEXT | |
| 9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR) |
![]() |
Disconnect the J77 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J77-3 (CANH) - J77-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to No. 5 Junction Connector) |
|
| ||||
| OK | ||
| ||
| 10.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - BLIND SPOT MONITOR SENSOR RH) |
![]() |
Disconnect the R17 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R17-5 (CANH) - R17-8 (CANL) | Ignition switch off | 200 Ω or higher |
| R17-5 (CANH) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-8 (CANL) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-5 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| R17-8 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 11.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R17-1 (CANH) - R17-4 (CANL) | Ignition switch off | 108 to 132 Ω |
| R17-1 (CANH) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-4 (CANL) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-1 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| R17-4 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 12.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R17-2 (CANH) - R17-3 (CANL) | Ignition switch off | 108 to 132 Ω |
| R17-2 (CANH) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-3 (CANL) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| R17-2 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| R17-3 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 13.CONNECT CONNECTOR |
Reconnect the R17 No. 6 junction connector.
| NEXT | |
| 14.CHECK FOR SHORT IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR RH) |
![]() |
Disconnect the S6 blind spot monitor sensor RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S6-2 (CA1P) - S6-7 (CA1N) | Ignition switch off | 54 to 69 Ω |
| S6-2 (CA1P) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| S6-7 (CA1N) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| S6-2 (CA1P) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| S6-7 (CA1N) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Blind Spot Monitor Sensor RH) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 15.CONNECT CONNECTOR |
Reconnect the R17 No. 6 junction connector.
| NEXT | |
| 16.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU) |
![]() |
Disconnect the J123 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J123-13 (CA2H) - J123-12 (CA2L) | Ignition switch off | 108 to 132 Ω |
| J123-13 (CA2H) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| J123-12 (CA2L) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| J123-13 (CA2H) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J123-12 (CA2L) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Network Gateway ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 17.CONNECT CONNECTOR |
Reconnect the R17 No. 4 junction connector.
| NEXT | |
| 18.CHECK FOR SHORT IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR) |
![]() |
Disconnect the J77 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J77-3 (CANH) - J77-2 (CANL) | Ignition switch off | 108 to 132 Ω |
| J77-3 (CANH) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| J77-2 (CANL) - J17-4 (CG) | Ignition switch off | 200 Ω or higher |
| J77-3 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J77-2 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 5 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 19.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Disconnect the J123 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J123-4 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J123-2 (BATT) - Body ground | Always | 11 to 14 V |
| J123-10 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| J123-9 (IG2) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Rear view of wire harness connector (to Network Gateway ECU) |
|
| ||||
| OK | ||
| ||