Home › DRIVE LINE › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

DTC    P17AC    Transfer Shift Motor Limit Switch Circuit

for Preparation Click here


DESCRIPTION

This DTC is detected when a malfunction is detected in the limit switch circuit, which detects the position of the transfer shift motor.

DTC Code
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P17AC
  1. When the ignition switch is ON, the engine is running, and the driving mode is being switched
  2. The combination of the TL1, TL2, TL3 and TL4 terminal signals is abnormal or the TL1, TL2, TL3 and TL4 terminal signal switching order is abnormal
  3. 0.02 seconds or more
  4. 1 trip detection logic
  1. Wire harness and connector
  2. 4 wheel drive control ECU
  3. Transfer shift actuator assembly

WIRING DIAGRAM

Refer to DTC P17AB .

INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
  1. Disconnect the A26 4 wheel drive control ECU connector.

  1. Disconnect the D68 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A26-18 (TL1) - D68-1 (TL1)
    Always
    Below 1 Ω
    A26-20 (TL2) - D68-2 (TL2)
    Always
    Below 1 Ω
    A26-26 (TL3) - D68-3 (TL3)
    Always
    Below 1 Ω
    A26-24 (TL4) - D68-4 (TL4)
    Always
    Below 1 Ω
    A26-22 (GTL) - D68-5 (GTL)
    Always
    Below 1 Ω
    A26-18 (TL1) or D68-1 (TL1) - Body ground
    Always
    10 kΩ or higher
    A26-20 (TL2) or D68-2 (TL2) - Body ground
    Always
    10 kΩ or higher
    A26-26 (TL3) or D68-3 (TL3) - Body ground
    Always
    10 kΩ or higher
    A26-24 (TL4) or D68-4 (TL4) - Body ground
    Always
    10 kΩ or higher
    A26-18 (TL1) - D68-2 (TL2), D68-3 (TL3), D68-4 (TL4) and D68-5 (GTL)
    Always
    10 kΩ or higher
    A26-20 (TL2) - D68-1 (TL1), D68-3 (TL3), D68-4 (TL4) and D68-5 (GTL)
    Always
    10 kΩ or higher
    A26-26 (TL3) - D68-1 (TL1), D68-2 (TL2), D68-4 (TL4) and D68-5 (GTL)
    Always
    10 kΩ or higher
    A26-24 (TL4) - D68-1 (TL1), D68-2 (TL2), D68-3 (TL3) and D68-5 (GTL)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
C291037E01
  1. Disconnect the transfer shift actuator assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D68-1 (TL1) - Body ground
    Ignition switch ON
    4 to 6 V
    D68-2 (TL2) - Body ground
    Ignition switch ON
    4 to 6 V
    D68-3 (TL3) - Body ground
    Ignition switch ON
    4 to 6 V
    D68-4 (TL4) - Body ground
    Ignition switch ON
    4 to 6 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transfer Shift Actuator Assembly)



NG
REPLACE 4 WHEEL DRIVE CONTROL ECU (Click here)
OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY (Click here)