Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM U

1UR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


CHECK ECM


U151401E02
2.313,0.26 2.688,0.49 0.375,0.229 10 false D74 5.542,0.26 5.917,0.49 0.375,0.229 10 false A24

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-1 (BATT) - D74-81 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
D74-41 (+BM) - D74-81 (E1) P - BR Power source of throttle actuator Always 11 to 14 V
A24-28 (IGSW) - D74-81 (E1) LG - BR Ignition switch Ignition switch ON 11 to 14 V
A24-3 (+B) - D74-81 (E1) GR - BR Power source of ECM Ignition switch ON 11 to 14 V
A24-2 (+B2) - D74-81 (E1) GR - BR Power source of ECM Ignition switch ON 11 to 14 V
D74-58 (OC1+) - D74-57 (OC1-) B - B-L Camshaft oil control valve (OCV) (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 1)
D74-52 (OC2+) - D74-51 (OC2-) L-B - R-B Camshaft oil control valve (OCV) (for Intake Side of Bank 2) Idling Pulse generation
(see waveform 1)
D74-56 (OE1+) - D74-55 (OE1-) L-W - L-B Camshaft oil control valve (OCV) (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 1)
D74-50 (OE2+) - D74-49 (OE2-) L-R - L Camshaft oil control valve (OCV) (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 1)
A24-34 (MREL) - D74-81 (E1) W - BR EFI relay Ignition switch ON 11 to 14 V
D74-74 (VG) - D74-75 (E2G) L-Y - G-W Mass air flow meter Idling, shift lever in P or N, A/C switch OFF 0.5 to 3.0 V
D74-73 (THA) - D74-98 (E2) Y-B - BR Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
D74-76 (THW) - D74-98 (E2) G-B - BR Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D74-80 (VCTA) - D74-79 (ETA) Y - L Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D74-78 (VTA1) - D74-79 (ETA) R-Y - L Throttle position sensor (for engine control) Ignition switch ON,
throttle valve fully closed
0.5 to 1.1 V
Ignition switch ON,
throttle valve fully open
3.2 to 4.8 V
D74-77 (VTA2) - D74-79 (ETA) Y-B - L Throttle position sensor (for sensor malfunction detection) Ignition switch ON,
throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON,
throttle valve fully open
4.6 to 5.0 V
A24-55 (VPA) - A24-58 (EPA) W - BE Accelerator pedal position sensor (for engine control) Ignition switch ON,
accelerator pedal released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
A24-56 (VPA2) - A24-60 (EPA2) LG - P Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON,
accelerator pedal released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 4.7 V
A24-57 (VCPA) - A24-58 (EPA) B - BE Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A24-59 (VCP2) - A24-60 (EPA2) V - P Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
D74-22 (HA1A) - D74-23 (E04) L - W-B A/F sensor heater Idling with warm engine Pulse generation
(see waveform 2)
D74-22 (HA1A) - D74-23 (E04) L - W-B A/F sensor heater Ignition switch ON 11 to 14 V
D74-20 (HA2A) - D74-21 (E05) G - W-B A/F sensor heater Idling with warm engine Pulse generation
(see waveform 2)
D74-20 (HA2A) - D74-21 (E05) G - W-B A/F sensor heater Ignition switch ON 11 to 14 V
D74-126 (A1A+) - D74-81 (E1) G -BR A/F sensor Ignition switch ON 3.3 V*1
D74-125 (A1A-) - D74-81 (E1) R - BR A/F sensor Ignition switch ON 2.9 V*1
D74-103 (A2A+) - D74-81 (E1) P - BR A/F sensor Ignition switch ON 3.3 V*1
D74-102 (A2A-) - D74-81 (E1) L - BR A/F sensor Ignition switch ON 2.9 V*1
D74-45 (HT1B) - D74-46 (E03) G-B - W-B Heated oxygen sensor heater Idling Below 3.0 V
D74-45 (HT1B) - D74-46 (E03) G-B - W-B Heated oxygen sensor heater Ignition switch ON 11 to 14 V
D74-44 (HT2B) - D74-46 (E03) B - W-B Heated oxygen sensor heater Idling Below 3.0 V
D74-44 (HT2B) - D74-46 (E03) B - W-B Heated oxygen sensor heater Ignition switch ON 11 to 14 V
D74-114 (OX1B) - D74-115 (EX1B) G - L Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(see waveform 3)
D74-112 (OX2B) - D74-113 (EX2B) R - W
D74-86 (#10) - D74-43 (E01) R-L - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
D74-109 (#20) - D74-43 (E01) L - W-B Idling Pulse generation
(see waveform 4)
D74-85 (#30) - D74-43 (E01) R - W-B
D74-108 (#40) - D74-43 (E01) Y - W-B
D74-84 (#50) - D74-43 (E01) G - W-B
D74-107 (#60) - D74-43 (E01) R - W-B
D74-83 (#70) - D74-43 (E01) W - W-B
D74-106 (#80) - D74-43 (E01) R-B - W-B
D74-94 (KNK1) - D74-93 (EKNK) R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 5)
D74-117 (KNK2) - D74-116 (EKN2) W - B
D74-96 (KNK3) - D74-95 (EKN3) W - B
D74-119 (KNK4) - D74-118 (EKN4) R - G
D74-92 (VV1+) - D74-91 (VV1-) R - G Variable valve timing (VVT) sensor (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 6)
D74-87 (VV2+) - D74-88 (VV2-) R - Y Variable valve timing (VVT) sensor (for Intake Side for Bank 2) Idling Pulse generation
(see waveform 6)
D74-69 (EV1+) - D74-68 (EV1-) R-L - B Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 17)
D74-64 (EV2+) - D74-65 (EV2-) R-L - B Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 17)
D74-110 (NE+) - D74-111 (NE-) W - Y Crankshaft position sensor Idling Pulse generation
(see waveform 6)
D74-40 (IGT1) - D74-81 (E1) B-Y - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 7)
D74-33 (IGT2) - D74-81 (E1) L-Y - BR
D74-37 (IGT3) - D74-81 (E1) B - BR
D74-34 (IGT4) - D74-81 (E1) L-B - BR
D74-35 (IGT5) - D74-81 (E1) G-R - BR
D74-36 (IGT6) - D74-81 (E1) G - BR
D74-38 (IGT7) - D74-81 (E1) G-W - BR
D74-39 (IGT8) - D74-81 (E1) G-B - BR
D74-104 (IGF1) - D74-81 (E1) G-B - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(see waveform 7)
D74-105 (IGF2) - D74-81 (E1) R - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(see waveform 7)
D74-63 (PRG) - D74-81 (E1) L-B - BR Purge VSV Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 8)
A24-13 (SPD) - D74-81 (E1) B - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(see waveform 9)
A24-46 (STA) - D74-81 (E1) R - BR Starter signal Cranking 5.5 V or more
D74-120 (NSW) - D74-81 (E1) L - BR Park/neutral position switch Ignition switch ON, shift lever position not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
A24-36 (STP) - D74-81 (E1) SB - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A24-35 (ST1-) - D74-81 (E1) R - BR Stop light switch
(opposite to STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
D74-19 (M+) - D74-82 (ME01) R - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 10)
D74-18 (M-) - D74-82 (ME01) G - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 11)
A24-52 (FPC) - D74-81 (E1) BE - BR Fuel pump control Ignition switch ON Below 1.5 V
A24-24 (W) - D74-81 (E1) P - BR MIL Ignition switch ON Below 3.0 V
Idling 11 to 14 V
A24-16 (TC) - D74-81 (E1) V - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A24-15 (TACH) - D74-81 (E1) GR - BR Engine speed Idling Pulse generation
(see waveform 12)
A24-30 (VPMP) - D74-81 (E1) V - BR Vent valve (built into canister pump module) Ignition switch ON 11 to 14 V
A24-49 (MPMP) - D74-81 (E1) W - BR Leak detection pump (built into canister pump module) Leak detection pump OFF Below 3.0 V
Leak detection pump ON 11 to 14 V
D74-67 (VCV1) - D74-98 (E2) L - BR Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D74-66 (VCV2) - D74-98 (E2) L - BR Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D74-121 (PPMP) - D74-98 (E2) P - BR Canister pressure sensor (built into canister pump module) Ignition switch ON 3.3 to 4.0 V
D74-32 (ALT) - D74-81 (E1) R - BR Generator Ignition switch ON 11 to 14 V
A24-10 (CANH) - D74-81 (E1) GR - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 13)
A24-11 (CANL) - D74-81 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 14)
D74-62 (ACIS) - D74-81 (E1) L-Y - BR VSV for ACIS (Acoustic Control Induction System) operation signal Ignition switch ON 11 to 14 V
D74-60 (HAI1) - D74-81 (E1) B - BR Air pump heater for secondary air injection system AI heater operating Below 1.5 V
D74-28 (AIRV) - D74-81 (E1) BR - BR Air switching valve for secondary air injection system Ignition switch ON 11 to 14 V
D74-54 (AIRP) - D74-81 (E1) P - BR Air pump control Ignition switch ON 11 to 14 V
D74-30 (AIDI) - D74-81 (E1) G - BR Diagnostic information signal for secondary air injection system Secondary air injection system operating Pulse generation
(see waveform 16)
A24-54 (AIP) - D74-98 (E2) Y - BR Secondary air injection system pressure signal Ignition switch ON 3.0 to 3.6 V
A24-43 (ARV2) - D74-81 (E1) V - BR Air switching valve for secondary air injection system Ignition switch ON 11 to 14 V
D74-53 (ARP2) - D74-81 (E1) P-L - BR Air pump control Ignition switch ON 11 to 14 V
D74-29 (AID2) - D74-81 (E1) G-Y - BR Diagnostic information signal for secondary air injection system Air injection system operating Pulse generation
(see waveform 16)
A24-53 (AIP2) - D74-98 (E2) G - BR Secondary air injection system pressure signal Ignition switch ON 3.0 to 3.6 V
D74-90 (G2) - D74- 89 (G2-) R - B Camshaft position sensor Idling Pulse generation
(see waveform 15)
A24-14 (STSW) - D74-81 (E1) BR - BR Starter switch Shift lever in P or N, cranking 6.0 V or more
A24-41 (ACCR) - D74-81 (E1) BR - BR ACC relay control signal Ignition switch ON → Cranking 11 to 14 V → Below 1 V
D74-16 (STAR) - D74-81 (E1) L - BR Starter relay control Ignition switch ON Below 1.5 V
Cranking 5.5 V or more
D74-72 (PSP) - D74-81 (E1) G - BR Power steering oil pressure sensor Ignition switch ON 0.5 to 4.5 V
D74-97 (PIM) - D74-98 (E2) L-R - BR Manifold absolute pressure sensor Idling 1.2 to 2.0 V
D74-48 (EGR1) - D74-81 (E1) B - BR EGR valve assembly Engine racing with warm engine Pulse generation
(see waveform 18)
D74-1 (EGR2) - D74-81 (E1) B-L - BR EGR valve assembly Engine racing with warm engine Pulse generation
(see waveform 19)
D74-24 (EGR3) - D74-81 (E1) B-R - BR EGR valve assembly Engine racing with warm engine Pulse generation
(see waveform 18)
D74-47 (EGR4) - D74-81 (E1) B-Y - BR EGR valve assembly Engine racing with warm engine Pulse generation
(see waveform 19)
A24-33 (ELS2) - D74-81 (E1) B - BR Electric load Defogger switch on 7.5 to 14 V
Defogger switch off Below 1.5 V
A24-4 (ADJ1)*2 - Body ground W-B - Body ground Vehicle type designation wire harness Always Below 1 V

HINT:

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


*2: Only for 2WD


b.
U115314E02
0.51,0.177 1.198,0.375 0.688,0.198 10 false 5 V/DIV. 0.552,1.104 0.99,1.302 0.438,0.198 10 false GND 1.802,1.833 2.698,2.031 0.896,0.198 10 false 1 msec./DIV.

WAVEFORM 1:

Camshaft Oil Control Valve (OCV)
Terminal No. (Symbol) Tool Setting Condition
D74-58 (OC1+) - D74-57 (OC1-) 5 V/DIV., 1 msec./DIV. Idling
D74-52 (OC2+) - D74-51 (OC2-) 5 V/DIV., 1 msec./DIV. Idling
D74-56 (OE1+) - D74-55 (OE1-) 5 V/DIV., 1 msec./DIV. Idling
D74-50 (OE2+) - D74-49 (OE2-) 5 V/DIV., 1 msec./DIV. Idling


c.
A172534E01
0.58,0.085 1.119,0.243 0.539,0.158 10 5 V/DIV. 0.739,1.488 1.073,1.671 0.334,0.183 10 GND 0.739,0.714 1.073,0.898 0.334,0.183 10 GND 1.664,1.737 2.555,1.923 0.891,0.186 10 10 msec./DIV. 3.074,0.969 3.374,1.127 0.300,0.158 10 CH2 3.074,0.11 3.374,0.268 0.300,0.158 10 CH1

WAVEFORM 2:

Air Fuel Ratio Sensor Heater
Terminal No. (Symbol) Tool Setting Condition
CH1: D74-22 (HA1A) - D74-23 (E04) 5 V/DIV., 10 msec./DIV. Idling with warm engine
CH2: D74-20 (HA2A) - D74-21 (E05) 5 V/DIV., 10 msec./DIV. Idling with warm engine

HINT:

The wavelength varies in accordance with the engine operating conditions.



d.
U115312E02
0.313,0.146 1.031,0.365 0.719,0.219 10 false 0.2 V/DIV. 0.531,1.479 0.917,1.677 0.385,0.198 10 false GND 1.802,1.865 2.802,2.063 1,0.198 10 false 200 msec./DIV.

WAVEFORM 3:

Heated Oxygen Sensor
Terminal No. (Symbol) Tool Setting Condition
D74-114 (OX1B) - D74-115 (EX1B) 0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
D74-112 (OX2B) - D74-113 (EX2B) 0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, item O2S B1S2 and O2S B2S2 show the ECM input values from the heated oxygen sensor.



e.
A363802E01
0.49,0.219 1.167,0.417 0.677,0.198 10 false 20 V/DIV. 1.833,1.885 2.792,2.063 0.958,0.177 10 false 20 msec./DIV. 0.604,1.573 0.99,1.771 0.385,0.198 10 false GND

WAVEFORM 4:

Fuel Injector No. 1 (to No. 8) Injection Signal
Terminal No. (Symbol) Tool Setting Condition
D74-86 (#10) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-109 (#20) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-85 (#30) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-108 (#40) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-84 (#50) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-107 (#60) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-83 (#70) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D74-106 (#80) - D74-43 (E01) 20 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



f.
A357198E02
2.406,0.531 3.052,0.708 0.646,0.177 10 false 1 V/DIV. 1.135,1.896 2.063,2.094 0.927,0.198 10 false 1 msec./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND

WAVEFORM 5:

Knock Sensor
Terminal No. (Symbol) Tool Setting Condition
D74-94 (KNK1) - D74-93 (EKNK) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D74-117 (KNK2) - D74-116 (EKN2) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D74-96 (KNK3) - D74-95 (EKN3) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D74-119 (KNK4) - D74-118 (EKN4) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine rpm increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




g.
A217926E01
0.24,1.161 0.470,1.326 0.230,0.165 10 (a) 0.24,1.707 0.455,1.859 0.215,0.151 10 (b) 0.24,2.075 0.479,2.280 0.239,0.206 10 (c) 2.819,1.267 3.155,1.416 0.336,0.149 10 GND 2.819,2.197 3.155,2.346 0.336,0.149 10 GND 2.819,1.815 3.155,1.964 0.336,0.149 10 GND 1.112,2.501 2.032,2.642 0.921,0.141 10 20 msec./DIV. 2.701,0.773 3.265,0.929 0.563,0.156 10 5 V/DIV.

WAVEFORM 6:

Crankshaft Position Sensor and VVT Sensor for Intake Side
Terminal No. (Symbol) Tool Setting Condition
(a) D74-110 (NE+) - D74-111 (NE-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
(b) D74-92 (VV1+) - D74-91 (VV1-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
(c) D74-87 (VV2+) - D74-88 (VV2-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up

HINT:

The wavelength becomes shorter as engine rpm increases.



h.
A379410E01
0.594,0.115 1.188,0.292 0.594,0.177 10 false 2 V/DIV. 0.604,0.896 0.979,1.073 0.375,0.177 10 false GND 0.594,1.458 0.969,1.635 0.375,0.177 10 false GND 0.938,0.719 1.177,0.906 0.24,0.188 10 false (a) 0.927,1.26 1.167,1.448 0.24,0.188 10 false (b) 1.833,1.813 2.854,1.99 1.021,0.177 10 false 20 msec./DIV.

WAVEFORM 7:

Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM)
Terminal No. (Symbol) Tool Setting Condition
(a) D74-40 (IGT1) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-33 (IGT2) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-37 (IGT3) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-34 (IGT4) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-35 (IGT5) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-36 (IGT6) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-38 (IGT7) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D74-39 (IGT8) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(b) D74-104 (IGF1) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(b) D74-105 (IGF2) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as engine rpm increases.



i.
A218020E20
2.677,0.333 3.302,0.542 0.625,0.208 10 false 10 V/DIV. 2.802,0.948 3.146,1.156 0.344,0.208 10 false GND 1.292,1.792 2.219,1.99 0.927,0.198 10 false 20 msec./DIV.

WAVEFORM 8:

Purge VSV
Terminal No. (Symbol) Tool Setting Condition
D74-63 (PRG) - D74-81 (E1) 10 V/DIV., 20 msec./DIV. Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



j.
U115313E02
0.396,0.229 1.083,0.427 0.688,0.198 10 false 2 V/DIV. 0.49,1.146 0.885,1.344 0.396,0.198 10 false GND 1.625,1.896 2.583,2.094 0.958,0.198 10 false 20 msec./DIV.

WAVEFORM 9:

Vehicle Speed Signal
Terminal No. (Symbol) Tool Setting Condition
A24-13 (SPD) - D74-81 (E1) 2 V/DIV., 20 msec./DIV. Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



k.
A208000E06
2.856,0.973 3.186,1.119 0.330,0.146 10 GND 2.631,0.216 3.176,0.360 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.237,1.806 2.058,1.964 0.820,0.158 10 1 msec./DIV.

WAVEFORM 10:

Throttle Actuator Positive Terminal
Terminal No. (Symbol) Tool Setting Condition
D74-19 (M+) - D74-82 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A245848E04
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

WAVEFORM 11:

Throttle Actuator Negative Terminal
Terminal No. (Symbol) Tool Setting Condition
D74-18 (M-) - D74-82 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



m.
A378423E01
0.573,0.656 1.208,0.854 0.635,0.198 10 false 5 V/DIV. 0.635,2.042 1.063,2.229 0.427,0.188 10 false GND 1.74,2.677 2.833,2.875 1.094,0.198 10 false 10 msec./DIV.

WAVEFORM 12:

Engine Speed Signal
Terminal No. (Symbol) Tool Setting Condition
A24-15 (TACH) - D74-81 (E1) 5 V/DIV., 10 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



n.
A357201E02
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.469,2.083 1,0.188 10 false 10 μsec./DIV.

WAVEFORM 13:

CAN Communication Signal (Reference)
Terminal No. (Symbol) Tool Setting Condition
A24-10 (CANH) - D74-81 (E1) 1 V/DIV., 10 μsec./DIV. Engine stopped and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



o.
A357202E02
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μsec./DIV.

WAVEFORM 14:

CAN Communication Signal (Reference)
Terminal No. (Symbol) Tool Setting Condition
A24-11 (CANL) - D74-81 (E1) 1 V/DIV., 10 μsec./DIV. Engine stopped and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



p.
A211721E01
2.827,1.417 3.206,1.598 0.379,0.181 10 GND 2.827,1.965 3.206,2.145 0.379,0.180 10 GND 0.146,1.87 0.458,2.033 0.312,0.163 10 CH2 0.146,1.321 0.456,1.484 0.310,0.163 10 CH1 1.123,2.469 2.063,2.645 0.941,0.177 10 20 msec./DIV. 2.696,0.738 3.261,0.914 0.566,0.177 10 5 V/DIV.

WAVEFORM 15:

Crankshaft Position Sensor and Camshaft Position Sensor
Terminal No. (Symbol) Tool Setting Condition
CH1: D74-110 (NE+) - D74-111 (NE-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
CH2: D74-90 (G2) - D74-89 (G2-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up

HINT:

The wavelength becomes shorter as the engine rpm increases.



q.
A100214E06
2.687,0.001 3.291,0.182 0.604,0.180 10 5 V/DIV. 1.063,1.87 1.976,2.051 0.913,0.180 10 50 msec./DIV.

WAVEFORM 16:

Terminal DI of Air Injection Control Driver
Terminal No. (Symbol) Tool Setting Condition
D74-30 (AIDI) - D74-81 (E1) 5 V/DIV., 50 msec./DIV. Performing system check using Techstream (secondary air injection check)
D74-29 (AID2) - D74-81 (E1) 5 V/DIV., 50 msec./DIV. Performing system check using Techstream (secondary air injection check)

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0412).



r.
A217927E01
0.263,1.166 0.493,1.331 0.230,0.165 10 (a) 0.263,1.711 0.459,1.894 0.196,0.183 10 (b) 0.263,2.083 0.473,2.252 0.210,0.169 10 (c) 2.827,1.272 3.164,1.421 0.336,0.149 10 GND 2.827,2.197 3.164,2.346 0.336,0.149 10 GND 2.827,1.824 3.164,1.973 0.336,0.149 10 GND 1.097,2.511 2.017,2.652 0.921,0.141 10 20 msec./DIV. 2.708,0.79 3.271,0.946 0.563,0.156 10 5 V/DIV.

WAVEFORM 17:

Crankshaft Position Sensor and VVT Sensor for Exhaust Side
Terminal No. (Symbol) Tool Setting Condition
(a) D74-110 (NE+) - D74-111 (NE-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
(b) D74-69 (EV1+) - D74-68 (EV1-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
(c) D74-64 (EV2+) - D74-65 (EV2-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up

HINT:

The wavelength becomes shorter as engine rpm increases.



s.
A174008E07
2.927,0.781 3.313,0.958 0.385,0.177 10 false GND 2.927,1.833 3.292,2 0.365,0.167 10 false GND 0.125,0.458 0.458,0.615 0.333,0.156 10 false CH1 0.125,1.427 0.479,1.594 0.354,0.167 10 false CH2 1.188,1.948 2.698,2.115 1.51,0.167 10 false 20 msec./DIV. 2.729,0.188 3.375,0.354 0.646,0.167 10 false 10 V/DIV.

WAVEFORM 18:

EGR Valve Signal
Terminal No. (Symbol) Tool Setting Condition
CH1: D74-48 (EGR1) - D74-81 (E1) 10 V/DIV., 20 msec./DIV. Engine racing with warm engine
CH2: D74-24 (EGR3) - D74-81 (E1) 10 V/DIV., 20 msec./DIV. Engine racing with warm engine


t.
A174007E07
2.875,1.813 3.229,1.99 0.354,0.177 10 false GND 2.875,0.802 3.229,0.979 0.354,0.177 10 false GND 0.188,0.542 0.521,0.729 0.333,0.188 10 false CH1 0.188,1.469 0.521,1.656 0.333,0.188 10 false CH2 1.24,1.938 2.271,2.115 1.031,0.177 10 false 20 msec./DIV. 2.667,0.26 3.281,0.417 0.615,0.156 10 false 10 V/DIV.

WAVEFORM 19:

EGR Valve Signal
Terminal No. (Symbol) Tool Setting Condition
CH1: D74-1 (EGR2) - D74-81 (E1) 10 V/DIV., 20 msec./DIV. Engine racing with warm engine
CH2: D74-47 (EGR4) - D74-81 (E1) 10 V/DIV., 20 msec./DIV. Engine racing with warm engine