Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0401  Exhaust Gas Recirculation Flow Insufficient Detected  


DESCRIPTION

Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to the engine's combustion chambers and thus lowers the combustion temperature to reduce NOx emissions. The ECM monitors signals such as engine speed, coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are fulfilled, the ECM controls the opening of the EGR valve linearly through signals to the EGR stepper motor.

DTC No. DTC Detection Condition Trouble Area
P0401 Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation
(2 trip detection logic)
·

EGR valve assembly

·

EGR passages

·

EGR cooler assembly

·

Manifold absolute pressure sensor

·

Intake system



MONITOR DESCRIPTION

The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction in the EGR valve assembly, illuminates the MIL and stores the DTC (2 trip detection logic).

MONITOR STRATEGY

Related DTC P0401: EGR valve high flow rate / low flow rate
Required sensors/Components (Main) EGR valve assembly, manifold absolute pressure sensor
Required sensors/Components (Related) Engine coolant temperature sensor, vehicle speed sensor
Frequency of operation Once per driving cycle
Duration 3 seconds
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs are not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (Knock Sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P0500 (Vehicle speed sensor)
P106A (Evaporative Emission System Pressure Sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
Time after engine started 3 seconds or more
Time after engine fuel cut 1 second or more
Engine speed 1200 to 1800 rpm
Vehicle speed 20 km/h (12.5 mph) or more
Engine speed change (per 65 msec.) -40 to 10 rpm
Time after engine load becomes stable (Brake, lock-up) More than 1 sec
Shift position Except "P" or "N" range
Engine coolant temperature 75°C (167°F) or more
Battery voltage 11 V or more
Intake air temperature -10°C (14°F) or more
Atmospheric pressure 76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS

Manifold pressure change Less than 1.8125 kPa (14 mmHg)
Engine speed 1400 rpm

CONFIRMATION DRIVING PATTERN

A217909E07
5.365,2.906 6.063,3.073 0.698,0.167 10 false 5 seconds 1.698,2.292 1.979,2.49 0.281,0.198 10 false [A] 2.24,2.031 2.531,2.24 0.292,0.208 10 false [B] 3.385,1.01 3.688,1.219 0.302,0.208 10 false [C] 5.667,1.573 5.948,1.833 0.281,0.26 10 false [F] 5.146,1.021 5.427,1.24 0.281,0.219 10 false [E] 4.563,3.365 4.875,3.552 0.313,0.188 10 false [D] 2.948,2.896 4.167,3.063 1.219,0.167 10 false 5 minutes or more 1.969,2.896 2.823,3.094 0.854,0.198 10 false Warming up 0.292,1.135 1.469,1.344 1.177,0.208 10 false 60 km/h (37 mph) 1.021,2.156 1.458,2.365 0.438,0.208 10 false Idling 0.219,2.385 1.458,2.573 1.24,0.188 10 false Ignition Switch ON 6.125,3.365 6.406,3.625 0.281,0.26 10 false [G]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for 30 seconds.

5.

Turn the ignition switch ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more [B].

HINT:

The A/C switch and all accessory switches should be off and the shift lever should be in P or N.


7.

Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 30 seconds or more [D].

9.

Drive the vehicle at 60 km/h (37 mph) and select the S4 range with the shift lever in S [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released [F].

HINT:

When "Idle Fuel Cut" in the Data List is ON, fuel cut is operating.


11.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Exhaust Gas Recirculation/VVT / Current [G].

12.

Check that the Exhaust Gas Recirculation/VVT / Current monitor is Complete.

HINT:

If the monitor is Incomplete, perform the driving pattern again.


13.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Exhaust Gas Recirculation/VVT / Details / EGR FLOW INSUFFICIENCY / Details.

14.

Check the test Details (EGR FLOW INSUFFICIENCY).

HINT:

Make sure that the values are between MIN and MAX.


15.

If the monitor is still Incomplete, perform the following procedure.

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

19.

Input the DTC: P0401.

20.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the DTC judgment result is INCOMPLETE or N/A and no pending DTC is output, drive the vehicle again at 60 km/h (37 mph) and select the S4 range with the shift lever in S, perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released, and then check the DTC judgment result.



21.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A217943E05
5.859,0.704 6.063,0.866 0.205,0.163 10 +B 5.859,1.08 6.299,1.236 0.441,0.156 10 MREL 5.494,0.71 5.761,0.866 0.267,0.156 10 A24 5.494,1.089 5.761,1.245 0.267,0.156 10 A24 5.579,0.535 5.706,0.695 0.128,0.160 10 3 5.536,0.907 5.740,1.066 0.204,0.159 10 34 5.859,3.068 6.282,3.243 0.423,0.175 10 EGR1 5.859,3.46 6.282,3.635 0.423,0.175 10 EGR2 5.859,3.853 6.282,4.027 0.423,0.175 10 EGR3 5.859,4.245 6.282,4.420 0.423,0.175 10 EGR4 2.601,3.166 3.025,3.341 0.423,0.175 10 EGR1 2.601,3.558 3.025,3.733 0.423,0.175 10 EGR2 2.601,3.951 3.025,4.126 0.423,0.175 10 EGR3 2.601,4.343 3.025,4.518 0.423,0.175 10 EGR4 5.482,3.072 5.783,3.221 0.302,0.149 10 D74 5.482,3.472 5.783,3.621 0.302,0.149 10 D74 5.482,3.857 5.783,4.006 0.302,0.149 10 D74 5.482,4.256 5.783,4.405 0.302,0.149 10 D74 5.537,2.896 5.720,3.052 0.184,0.156 10 48 5.572,3.288 5.686,3.444 0.114,0.156 10 1 5.551,3.674 5.741,3.830 0.191,0.156 10 24 5.544,4.08 5.734,4.229 0.191,0.149 10 47 6.09,4.802 6.433,4.958 0.343,0.156 10 ECM 4.773,2.224 5.439,2.376 0.665,0.152 10 EFI NO. 2 3.911,0.711 4.117,0.866 0.205,0.155 10 1B 3.956,0.528 4.070,0.688 0.114,0.160 10 4 3.911,1.089 4.117,1.244 0.205,0.155 10 1B 3.956,0.906 4.070,1.066 0.114,0.160 10 2 1.474,0.711 1.679,0.866 0.205,0.155 10 1C 1.518,0.528 1.632,0.688 0.114,0.160 10 1 1.474,1.089 1.679,1.244 0.205,0.155 10 1B 1.518,0.906 1.632,1.066 0.114,0.160 10 3 1.929,0.83 2.571,0.979 0.642,0.149 10 EFI NO. 1 2.901,1.341 3.163,1.504 0.262,0.163 10 EFI 2.237,1.88 3.338,2.057 1.100,0.177 10 Integration Relay 3.078,2.98 3.199,3.136 0.121,0.156 10 4 3.078,3.373 3.199,3.528 0.121,0.156 10 3 3.078,3.765 3.199,3.921 0.121,0.156 10 6 3.078,4.157 3.199,4.313 0.121,0.156 10 1 3.078,4.918 3.199,5.074 0.121,0.156 10 5 3.078,4.554 3.199,4.710 0.121,0.156 10 2 2.728,5.096 3.010,5.253 0.282,0.157 10 +B1 2.728,4.743 3.010,4.900 0.282,0.157 10 +B2 1.915,5.355 2.203,5.504 0.288,0.149 10 D85 1.915,5.502 2.640,5.658 0.725,0.156 10 EGR Valve 0.703,4.893 1.185,5.062 0.482,0.170 10 Battery

CAUTION / NOTICE / HINT

HINT:
·

By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.

·

When the engine is idling steadily with the EGR valve fully closed, if the EGR valve is normal and it is opened using the Active Test, the Data List values will change as follows.

Data List Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test
Engine Speed Idle becomes rough
MAP Pressure rises

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0401)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0401 is output A
DTC P0401 and other DTCs are output B

HINT:

If any DTCs other than P0401 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
- MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

3.INSPECT EGR VALVE ASSEMBLY

NG

4.REPLACE EGR VALVE ASSEMBLY
3.INSPECT EGR VALVE ASSEMBLY
a.

Confirm that there are no deposits on the EGR valve.


b.

Confirm that the EGR valve is closed.

OK:

There are no deposits and the valve is closed.




OK

5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)

NG

4.REPLACE EGR VALVE ASSEMBLY
4.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)
5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)
A217946

a.

Check for exhaust leaks at each connection point.


b.

Check for cracks, damage and blockage of the pipes between the intake manifold converter and EGR valve assembly.

HINT:

This check may require the removal of components.



c.

Check for blockage due to deposits in the EGR valve and pipes.

OK:

No deposits.




OK

6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY)
A379429

a.

Check for exhaust leaks at each connection point.


b.

Check for cracks, damage and blockage of the pipes between the exhaust manifold converter and EGR valve assembly.

HINT:

This check may require the removal of components.



c.

Check for blockage due to deposits in the EGR valve and pipes.

OK:

No deposits.




OK

7.INSPECT EGR COOLER ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

7.INSPECT EGR COOLER ASSEMBLY
a.

Check for blockage in the EGR cooler assembly.



OK

8.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

REPAIR OR REPLACE EGR COOLER ASSEMBLY

8.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


e.

Read the MAP value.

Standard:
Switch Condition Techstream Display
Ignition switch ON 80 to 110 kPa (600 to 825 mmHg)



f.

Read the MAP value when racing the engine.

Standard:
Engine Condition Techstream Display
Idling 20 to 40 kPa (150 to 300 mmHg)




OK

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

9.CHECK INTAKE SYSTEM
9.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>1UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

REPAIR OR REPLACE INTAKE SYSTEM

10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

HINT:

The A/C switch and all accessory switches should be off.



h.

Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more.

CAUTION:

Strictly observe speed limits and traffic laws when performing the confirmation drive pattern.



i.

Idle the engine for 30 seconds or more.


j.

Drive the vehicle at 60 km/h (37 mph).

CAUTION:

Strictly observe speed limits and traffic laws when performing the confirmation drive pattern.



k.

Perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released.

HINT:

If the deceleration was not completed, perform the Confirmation Driving Pattern again.



l.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


m.

Read the pending DTCs.


n.

If a pending DTC is output, the system is malfunctioning.

HINT:

If a pending DTC is not output, perform the following procedure.



o.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


p.

Input the DTC: P0401.


q.

Check the DTC judgment result.

Result:
Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit






NEXT

END